SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Battery Holder: Four C Cells in Two Sprung Compartments with a Z-Shaped Retainer (Lund 1979)
A tray for four C cells in series, made for an instrument that gets knocked about. Each compartment holds two cells end to end, pressed together by a cone-shaped coil spring. The cells can shift a little under a blow and spring back without losing contact. A small Z-shaped retainer holds down one cell in each row and still lets every cell be taken out.
Source: John Lund, US 4,161,568 (Schonstedt Instrument Co., 1979), with all sizes. Unknown: the plastic, the metals and the spring wire size. Lund names none of them, and nothing makes a self-tapping screw yet, so these are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 1.
Kati
1 day
Maagizo
1
1
Mould the tray
Mould the tray
Mould a tray 4.325 × 2.500 × 0.875 in (109.9 × 63.5 × 22.2 mm) with two parallel open-top compartments, each 4.125 in long, 1.025 in wide and 0.800 in deep inside (104.8 × 26.0 × 20.3 mm). The middle wall is 0.300 in (7.6 mm) thick, with a notch at one end. Mould two small abutments on the middle wall, 1.000 in (25.4 mm) apart. Unknown: the plastic.
Vifaa kwa hatua hii:
Kihami kisichojulikana1 as requiredZana zinazohitajika:
Kalibu ya kubana
Kalipa ya Vernier2
2
Wind the two spring contacts
Wind the two spring contacts
Wind two cone-shaped coil springs: 0.562 in (14.3 mm) outside diameter at the large end, 0.312 in (7.9 mm) inside at the small end, 1/2 in (12.7 mm) long free, closing to 1/8 in (3.2 mm). Each has three active turns, and the end turns are wound flat. Leave one spring with a long straight tail. Unknown: the metal and the wire size.
Vifaa kwa hatua hii:
Metali isiyojulikana1 as requiredZana zinazohitajika:
Koleo lenye Ncha za Duara
Koleo la Mdomo BapaKalipa ya Vernier3
3
Fit the contacts and terminals
Fit the contacts and terminals
Put one spring at the far end of the first compartment, with its straight tail, and the other at the near end of the second. Set an eyelet contact in the end wall opposite each spring. Run the tail through the notch in the middle wall to the eyelet contact at the far end of the second compartment. Fix two terminals to the near end wall with eyelets, each holding its contact.
Vifaa kwa hatua hii:
Metali isiyojulikana1 as requiredZana zinazohitajika:
Mkasi wa batiKoleo la Mdomo Bapa
Tupa za mkono4
4
Make and fix the retainer
Make and fix the retainer
Cut a flat Z-shaped retainer of plastic, 0.062 in (1.6 mm) thick and 0.980 in (24.9 mm) long. It is 0.430 in (10.9 mm) wide at each branched end. Each branch sticks out 0.130 in (3.3 mm) from the stem and runs 0.365 in (9.3 mm) along it. Screw it with a single self-tapping screw through the middle of the stem onto the top of the middle wall, between the abutments, so it cannot turn. Each branch reaches over one compartment.
Vifaa kwa hatua hii:
Kihami kisichojulikana1 as required
Skrubu ya kujikatia hesi1 pcZana zinazohitajika:
Mkasi wa batiTupa za mkono
Seti ya bisibisiKalipa ya Vernier5
5
Wire it
Wire it
Solder lead wires to the two terminals. With the cells in, the four make one series supply between these terminals.
Vifaa kwa hatua hii:
Waya wa kuunganishia1 as required
Waya wa Lehemu1 as requiredZana zinazohitajika:
Chuma cha kulehemia6
6
Load the cells
Load the cells
Put cell 1 into the free end of the first compartment, slide it along under the retainer until it meets the spring, then drop cell 2 in behind it, pressing the spring a little. Load the second compartment from its other end the same way. To unload, lift out the two free cells, then slide the held cells along into their places and lift them out. Ours: check the voltage across the terminals with a meter.
Zana zinazohitajika:
Kipima-umeme cha aina nyingiVifaa
5- 1 as requiredKishikilia Nafasi
- 1 as requiredKishikilia Nafasi
- Kishikilia Nafasi
- 1 as requiredKishikilia Nafasi
- 1 as requiredKishikilia Nafasi
Zana Zinazohitajika
9- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 2 vendors sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.