Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI

Five-Foot Bait-Casting Rod: Hand-Tapered Dagame Stick, Cork Grasps and Agate Guides (Boy Mechanic, 1915)
Stillman Taylor's first rod for a beginner, from The Boy Mechanic, Book 2 (1915): a one-piece 5 ft bait-casting rod planed by hand from a 5/8 in square stick of dagame to his calipered taper (1/2 in at the grasp to 1/8 in at the tip), with a double cork grasp around the reel seat, two agate guides and an agate tip, whipped in silk and varnished. He made it with "a saw, plane, jackknife, file, and sandpaper".
Kati
About 2 weeks (glue and varnish drying)
Maagizo
1
1
Fig. 5: the taper, station by station
Fig. 5: the taper, station by station
Inapakia daftari la Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"The short one-piece bait-casting rod with but one ferrule is the easiest rod to make." His materials: 1 dagame or greenheart stick, 5 ft long and 5/8 in square; 1 reel seat with straight hood, 3/4 in; 1 butt cap, 1 in; 1 taper, small end 15/32 in; 1 offset agate top, 3/32 in, and 2 narrow agate guides, 1/2 in, all in German silver; 2 doz. corks, 1-1/4 by 1-1/8 in; two 50 yd spools of silk, red and green, 00 size.
3
3
Make the gauge and grooved board
Make the gauge and grooved board
On a strip of paper draw the rod full length: a 1/2 in line for the butt, a centre line 60 in long, a 1/8 in line at the tip, and join the ends. From 12 in, mark a crossline every 6 in and write his diameters on them (see the notebook). File nine slots in a thin strip of brass to these diameters as a gauge. Plane a groove, gradually shallower toward one end, in a 5 ft tongue-and-groove pine board about 1 in thick, and nail it to the bench edge, groove up.
Vifaa kwa hatua hii:
Bamba la Shaba ya Njano1 kipande
Ubao wa msonobari1 kipande
Misumari1 kipandeZana zinazohitajika:
Karatasi ya kahawia ya kufungia
Penseli
Tupa (Tupa ya Mkono)
Kibano cha meza ya kazi
Kalipa ya Vernier
Randa ya mkono
Nyundo
Tepi ya kupimia4
4
Plane the stick square and tapered
Plane the stick square and tapered
Plane along each side and from both ends of a 5/8 in square dagame strip to find the grain. Drill two holes about 1/4 in from the butt end and hook them over a brad in the bench corner, so you plane with the grain. Plane it straight and true to 1/2 in square, evenly from all sides, ignoring kinks. Knife-mark the hand grasp 12 in from the butt (11 in for a single grasp). Then plane an even taper from butt to tip, checking with caliper and gauge at every 6 in mark and planing the thick spots lightly. Bend the tip on the floor: if it stays bent, the wood needs a few weeks' seasoning in a warm place.
Vifaa kwa hatua hii:
Mbao ya dagame1 kipande
Misumari1 kipandeZana zinazohitajika:
Randa ya mkono
Randa ndogo ya kiganja
Jiwe la Kunolea
Kekee cha mkono
Kalipa ya Vernier
Kisu cha kazi za mikono
Nyundo5
5
Round the rod
Round the rod
Lay the rod in the grooved board, a corner up, and take each corner off with a finely set small plane to make it eight-sided, calipering every 6 in mark and keeping the eight sides even, until it is almost round and tapers evenly from the grasp mark to the tip. File grooves across the edge of a cabinetmaker's steel scraper with a round file, sharpen them, and scrape the rod perfectly round; sandpaper it smooth. Tie on the tip and guides and string the reel on to try a few casts, then smooth it with No. 0 sandpaper.
Vifaa kwa hatua hii:
Sandarusi (karatasi ya kusugua)1 kipandeZana zinazohitajika:
Randa ndogo ya kiganja
Kikwaruzi cha chuma
Tupa (Tupa ya Mkono)
Kalipa ya Vernier6
6
Build the lower grasp and reel-seat sleeve
Build the lower grasp and reel-seat sleeve
Cut a hole in the corks with a sharpened tube turned like a wad cutter. Cut the butt off square about 1 in from the end, to remove the holes. Glue on a cork with hot glue, then cork after cork, about 10, for a grasp a trifle over 5 in long. For the reel-seat sleeve, bore a 15/32 in hole through white pine about 3/4 in thick and 5 in long, plane the outside to slip inside the reel seat, taper one end to match it, and make it about 1/4 in shorter than the reel seat. Glue it down on top of the last cork and leave the glue a day or two.
Vifaa kwa hatua hii:
Pete za kizibo10 vipande
Gundi ya wanyama1 kipande
Ubao wa msonobari1 kipandeZana zinazohitajika:
Neli ya shaba nyeupe
Tupa (Tupa ya Mkono)
Msumeno wa mkono
Kekee cha mkono
Randa ndogo ya kiganja7
7
Fit the butt cap and reel seat
Fit the butt cap and reel seat
Trim the grasp to about 1-1/16 in diameter (1-1/4 in corks need little trimming), leaving the top cork as a shoulder, and fit the lower corks to the butt cap's taper. Heat the cap moderately, rub melted ferrule cement inside and force it on; when hard, drive a small brass pin or brad through and file it flush. Cut the 4-1/2 in reel seat down to 3-7/8 in and fit it with the hood at the lower end, worked into the cork for a tight joint. Cement the sleeve, push the reel seat home and drive a small pin through the hood into the wood a short way only, not through the rod.
Vifaa kwa hatua hii:
Kifuniko cha kitako cha fimbo1 kipande
Kishikio cha reli1 kipande
Gundi ya feruli1 kipandeZana zinazohitajika:
Kisu cha kazi za mikono
Tupa (Tupa ya Mkono)
Tochi ya Propani
Nyundo8
8
Build the upper grasp and finish the wood
Build the upper grasp and finish the wood
Cement corks above the reel seat, the first pressed against the seat and turned so the metal enters it, then shape them into a smooth swelled grasp and cement on the winding check. Sand the rod, wet it to raise the grain, and sand again with old paper; for a finer polish rub with pumice and oil and an oiled rag. File the tip to fit the agate top, smear on melted ferrule cement and push the top home. Rub the wood over with a cloth wet with varnish to fill the pores, and wipe off the surplus.
Vifaa kwa hatua hii:
Pete za kizibo6 vipande
Gundi ya wanyama1 kipande
Pete ya kumalizia mshiko1 kipande
Pete ya ncha ya fimbo1 kipande
Gundi ya feruli1 kipande
Sandarusi (karatasi ya kusugua)1 kipande
Varnishi ya magari ya farasi1 kipandeZana zinazohitajika:
Kisu cha kazi za mikono
Tupa (Tupa ya Mkono)
Tochi ya Propani9
9
Whip on the guides
Whip on the guides
Place the first guide 19-1/2 in from the metal taper above the upper grasp and the second 15-1/2 in further on; round the sharp edges of their bases with a fine file and hold them with a few turns of common thread. Whip with 00 silk using the invisible knot: tuck the end under the first coil, wind tightly by turning the rod, lay a waxed loop of silk about 4 in long under the last turns, wind about 1/8 in beyond the pointed flange, cut the silk and pull its end back under with the loop. About a dozen turns make a winding; edgings of three or four turns go on after, in red with green or yellow.
Vifaa kwa hatua hii:
Pete ya kuongoza uzi wa fimbo2 vipande
Hariri ya kuzongea fimbo1 kipande
Uzi wa kitani1 kipande
Nta ya Nyuki1 kipandeZana zinazohitajika:
Tupa (Tupa ya Mkono)
Kisu cha kazi za mikono10
10
Shellac and varnish
Shellac and varnish
Clip any fuzzy ends and give the silk two light coats of white shellac dissolved in grain alcohol, warmed and laid on with a small camel's-hair brush; let it dry a couple of days. Warm the coach varnish in a pot of hot water for five minutes and brush it on evenly with a brush about 1/2 in wide, in a warm place (about 75 deg F). Hang the rod by the tip in a dust-free room; allow three days between coats; two coats protect it, three give complete protection.
Vifaa kwa hatua hii:
Vanishi ya shelaki1 kipande
Varnishi ya magari ya farasi3 vipandeZana zinazohitajika:
Brashi pana ya rangi11
11
Troubleshooting
Troubleshooting
Casting rod troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
From "Fishing-Rod Making and Angling, Part I -- A One-Piece Casting Rod" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 59-66). His text says about 10 corks for the lower grasp; his list allows 2 dozen for both grasps. The block plane, vernier caliper and other modern tool names, and the metric figures, are ours; his tools were "a saw, plane, jackknife, file, and sandpaper" plus those in his tools section.
Vifaa
18- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 10 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 4 vipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
17- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

