Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI

Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)
R. H. Allen's four-passenger coasting bob from The Boy Mechanic, Book 2 (1915): a 6-1/2 ft top board with four hinged seat backs, carried on two short sleds with ash runners shod in 5/8 in round iron. The rear sled rocks on a wedge and hinges to follow the ground; the front sled steers by a broom-handle post and a wheel made from a nail-keg hoop. Every size is his.
Kati
About 3 days
Maagizo
1
1
His list of materials in centimetres
His list of materials in centimetres
Inapakia daftari la Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"Any wood may be used for the sled, except for the runners, which should be made of ash." His list of materials: 1 top 6-1/2 ft x 16 in x 1-1/4 in; 4 runners 22 x 4 x 1 in; 4 crosspieces 16 x 3 x 1 in; 3 pieces 16 x 5 x 2 in; 1 piece 16 x 5 x 1 in; 1 shore 16 x 3 x 1 in; 4 seat backs 12 x 16 x 1 in; 1 dowel 3 ft x 1 in; 4 rods 5/8 in x 30 in; 4 eyebolts 1/2 x 6 in; 3 hinges 5 in strap; 8 hinges 3 in strap.
3
3
Shape and shoe the runners
Shape and shoe the runners
Cut one ash runner to shape and use it as the pattern for the other three. Cut a groove about 1/4 in deep along the under edge to take the curve of a 5/8 in round iron rod. Bend each rod to fit in the groove, up the back of the runner and over the top at the front; flatten the ends and drill two holes in each for wood screws (a blacksmith can flatten them, he says). Screw the irons on.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu1 kipande
Fimbo ya chuma4 vipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Msumeno wa kukata mikunjo
Patasi
Jiko la mgongo la makaa ya mawe
Fuawe
Nyundo ya mhunzi
Kibano cha meza ya kazi
Kekee cha mkono
Penseli4
4
Build the two sleds
Build the two sleds
Notch the top edges of each pair of runners for the 16 x 3 in crosspieces, near the ends, so the crosspieces lie flush with the runner tops and the notches of each pair line up. Fit them snugly, fasten with long, slim wood screws, and stiffen each joint inside with a small metal brace.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipande
Parafujo za mbao1 kipande
Bano la pembe8 vipandeZana zinazohitajika:
Msumeno wa mkono
Patasi
Kekee cha mkono5
5
Make the rocking rear joint
Make the rocking rear joint
Cut a heavy 2 x 5 in crosspiece sloping across its width, from 2 in thick at one edge to a feather edge at the other. Fix the three large strap hinges to the sloping face, and fasten the piece solidly on the rear sled's runners with its centre 8 in from their front ends. This lets the rear sled rock but not turn sideways.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipande
Bawaba ya ukanda ya chuma3 vipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Randa ya mkono
Kekee cha mkono6
6
Mount the front sled crosspiece
Mount the front sled crosspiece
Fasten the supporting crosspiece on top of the front sled's runners with its centre 11 in from their front ends.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Kekee cha mkono
Tepi ya kupimia7
7
Brace the top board
Brace the top board
Round both ends of the top board and plane it smooth. Underneath, fit two crosspieces, each with two 1/2 in holes bored through its width near the ends for the eyebolts: one with its centre 12 in from the rear end, the other 8 in from the front. Screw them on. Set the shore in the centre of the board, run wires over it between the eyebolts, and draw the eyebolts up until the wire is taut over the shore, so the long board cannot sag.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipande
Bolti yenye jicho4 vipande
Waya wa chuma uliovutwa kwa bamba1 kipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Randa ya mkono
Kekee cha mkono chenye ncha
Tepi ya kupimia8
8
Fit the seat backs and foot rests
Fit the seat backs and foot rests
Round the top corners of the four backs and cut the bottom ends at a slight angle for a slant. Hinge them to the top board with the small strap hinges every 18 in, starting at the rear. Bore 1 in holes about 1 in deep in the edges of the top board every 18 in, beginning about 5 in from the front, and drive in pins 4 in long cut from the dowel, as foot rests.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipande
Bawaba ya ukanda ya chuma8 vipande
Vijiti vya mbao ngumu1 kipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Kekee cha mkono chenye ncha
Tepi ya kupimia9
9
Make the steering
Make the steering
Cut a broom handle to 18 in and fasten one end in a hole bored centrally in the 5 in crosspiece of the front sled. Bore a hole in the top board through the centre of the crosspiece underneath; put two metal washers on the stick and run it up through the hole, then fasten a hardwood collar to it just above the board so the top cannot lift off the sled. For the wheel, fasten a piece of wood across a nail-keg hoop, cover the hoop with garden hose and wrap it with twine; bore the centre of the crosspiece to fit the broom handle and screw it on.
Vifaa kwa hatua hii:
Ufagio1 kipande
Washa bapa2 vipande
Ubao wa Mti Mgumu1 kipande
Pete ya chuma1 kipande
Mpira wa bomba1 kipande
Kamba nyembamba ya juti1 kipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Kekee cha mkono chenye ncha
Kekee cha mkono10
10
Join the sleds and fit the ropes
Join the sleds and fit the ropes
Fasten the rear sled to the top board with screws through the free wings of the hinges into the crosspiece. Bore holes in the front ends of all runners and attach a chain or rope: the rear one's loop to the underside of the top board, the front one for drawing the sled.
Vifaa kwa hatua hii:
Parafujo za mbao1 kipande
Mnyororo wa chuma1 kipandeZana zinazohitajika:
Kekee cha mkono chenye ncha
Kekee cha mkono11
11
Troubleshooting
Troubleshooting
Bobsled troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
From "Four-Passenger Coasting Bobsled" by R. H. Allen, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 24-26). The runner shape comes from his drawing, not from figures. The scan calls the steering collar a hardwood collar; the Gutenberg text drops "hardwood". The tools and metric figures are ours.
Vifaa
15- 1 kipandeKishikilia Nafasi
- 4 vipandeKishikilia Nafasi
- 8 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 8 vipandeKishikilia Nafasi
- 8 vipandeKishikilia Nafasi
- 4 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
12- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

