Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
7
0
0
0
0

Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)

A six-string guitar "having straight lines, giving it an old-fashioned appearance", from The Boy Mechanic (1913): a tapered box of hard maple with a seasoned soft-pine top, a drawknifed neck, frets cut from hatpins and a 24 in scale. Sizes are read on the 1913 scan. "If care is taken in selecting the material, and having it thoroughly seasoned, the finished instrument will have a fine tone."
Juu
About 1 week, with glue drying

Maagizo

1

Cutting list and frets

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic

"The sides, ends and bottom are made of hard wood, preferably hard maple, and the top should be made of a thoroughly seasoned piece of soft pine." (J. H. Stoddard, Carbondale, Pa.)
3

Cut the pieces

Cut from thoroughly seasoned wood: top 3/16 by 14 by 17 in (soft pine); bottom 3/16 by 14 by 17 in, two sides 3/16 by 3-5/8 by 16-3/4 in, and ends 3/16 by 3-5/8 by 13-1/8 in and 9-5/8 in (hard maple); neck 1 by 2-5/16 by 18-1/2 in; fingerboard 3/16 by 2-5/8 by 16 in.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
Ubao wa msonobariUbao wa msonobari1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Tepi ya kupimiaTepi ya kupimia
Kipima pembe cha nyuzi tisiniKipima pembe cha nyuzi tisini
4

Shape the neck and fingerboard

Taper the neck from G to F and from J to F, with the back rounded, using a drawknife: 2-3/8 in at the heel, 1-7/8 in at the nut F, and a head 2-3/4 in wide and 6-1/2 in long. Taper the fingerboard to match. Glue a piece of hard wood 1/4 in square and 1-7/8 in long across the neck at F as the nut. Glue the fingerboard to the neck and clamp it until the glue sets.

Vifaa kwa hatua hii:

Utepe wa mbao gumuUtepe wa mbao gumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Kisu cha KuvutaKisu cha Kuvuta
Msumeno wa mkonoMsumeno wa mkono
Kibano cha upauKibano cha upau
5

Fret the fingerboard

Mark the frets from the nut using the computed positions in step 1 (fret 1 at 1.347 in, fret 12 at 12 in). His drawing gives only five spaces, 1-2/5, 1-3/16, 1-1/8, 1-1/16 and 1 in; added up they put the 5th fret about 0.3 in short of the true place, so they are shown for history only. Cut pieces from hatpins and fasten them across the fingerboard with small wire staples. Mark accurately: the frets decide the pitch.

Vifaa kwa hatua hii:

Pini ya kofiaPini ya kofia1 kipande
Stapuli ya wayaStapuli ya waya1 kipande

Zana zinazohitajika:

Koleo la Mdomo BapaKoleo la Mdomo Bapa
NyundoNyundo
Tepi ya kupimiaTepi ya kupimia
Kipima pembe cha nyuzi tisiniKipima pembe cha nyuzi tisini
6

Build the box

Glue the sides and ends together, so the body is 10 in wide at the neck end, 13-1/2 in at the tail and 16-1/2 in long. Glue the front on, put heavy weights on top and give the glue time to dry. Fasten pieces of soft wood in the corners as braces, glue a small block C inside the neck end to take the bolt, and glue strips of soft wood K across the front and back to strengthen them. Cut the sound hole in the top as drawn.

Vifaa kwa hatua hii:

Papi ya mbao lainiPapi ya mbao laini1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kibano cha upauKibano cha upau
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
7

Fit the neck

Make the brace D 1 in thick, to any shape you like. Glue the neck to the box and secure it with a carriage bolt at A through the end and block C. Glue the back on and smooth the outside with sandpaper.

Vifaa kwa hatua hii:

Utepe wa mbao gumuUtepe wa mbao gumu1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara1 kipande
Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)1 kipande

Zana zinazohitajika:

Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kibano cha upauKibano cha upau
8

Make and place the bridge

Make the bridge 6 in long, 1 in wide and 3/8 in high, with an old hatpin or wire of the same size secured on top with pin staples as the saddle E. Drill six 3/16 in holes in it for the pins. Glue it on the top so the distance from the nut F to the saddle E is just 24 in.

Vifaa kwa hatua hii:

Utepe wa mbao gumuUtepe wa mbao gumu1 kipande
Pini ya kofiaPini ya kofia1 kipande
Stapuli ya wayaStapuli ya waya1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Msumeno wa mkonoMsumeno wa mkono
Tepi ya kupimiaTepi ya kupimia
9

String it

Fit the turning pegs B in the head and string the guitar, holding the strings in the bridge with the pins. He bought the pegs and strings from a music store.

Vifaa kwa hatua hii:

Vigingi vya Kupanga SautiVigingi vya Kupanga Sauti1 kipande
Nyuzi za gitaaNyuzi za gitaa1 kipande
Pini za daraja la gitaaPini za daraja la gitaa1 kipande

Zana zinazohitajika:

Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
10

Troubleshooting

Guitar troubleshooting.

Flow

Loading...
11

History and honest limits

From **The Boy Mechanic**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913, p. 320, "A Guitar That Is Easy to Make", sent in by J. H. Stoddard of Carbondale, Pa.; sizes read on the 1913 scan (archive.org boymechanicthing01unse). He dimensions only the first five fret spaces, and they disagree with equal temperament; the fret positions used are computed by us. The sound hole, saddle and string tensions are not dimensioned. The tools and metric figures are ours.

Vifaa

12

Zana Zinazohitajika

8

Mchoro huu unatengeneza

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...