SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
BAADAYE YA KIJANI
REVERSE ENGINEERING
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Building a Methane Gas Leak Detector
Ed

Imeundwa na

Ed

13. Julai 2026FI
0
0
0
0
0

Building a Methane Gas Leak Detector

Build a circuit that sniffs out methane — the main component of natural gas — and alarms when it rises. An MQ-4 sensor's reading climbs when combustible gas is present; the Arduino compares it to clean air and triggers a buzzer and red LED. A great combustible-gas sensing project — with two honest notes: methane is flammable, and this is a demonstration, NOT a certified gas-leak detector.

Kati
1-2 hours

Maagizo

1

Wire the sensor, buzzer and LED

On the breadboard: MQ-4 VCC to Arduino 5V, GND to GND, and its analog output (AOUT) to A0. Active buzzer + to pin 8, - to GND. Red LED anode to pin 7 through a 330 Ω resistor, cathode to GND.

Vifaa kwa hatua hii:

Arduino Uno R3Arduino Uno R31 kipande
Methane CNG Gas Sensor - MQ-4Methane CNG Gas Sensor - MQ-41 kipande
Active Buzzer Module (5V, 5-Pack)Active Buzzer Module (5V, 5-Pack)1 kipande
LED - Basic 5mmLED - Basic 5mm1 kipande
Resistor 330 Ohm 1/6 Watt PTH - 20 packResistor 330 Ohm 1/6 Watt PTH - 20 pack1 paketi
BreadboardBreadboard1 kipande
Jumper Wires (Male-to-Male)Jumper Wires (Male-to-Male)1 paketi
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

Vifaa kwa hatua hii:

USB-B CableUSB-B Cable1 kipande

Zana zinazohitajika:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the detector sketch

Paste this sketch and upload. It warms the sensor, records a clean-air baseline, then sounds the buzzer and lights the LED whenever the reading rises above that baseline.

methane_detector.inoarduino
// Methane / natural-gas leak INDICATOR using an MQ-4 sensor.
// NOT a certified gas-leak detector - see the safety note. Methane is flammable.
// MQ-4 analog output on A0; buzzer on pin 8; red warning LED on pin 7.

const int MQ4_PIN = A0;
const int BUZZER_PIN = 8;
const int LED_PIN = 7;

int cleanAirValue = 0;          // baseline, measured at startup
const int ALARM_MARGIN = 150;   // how far above baseline triggers the alarm

void setup() {
  pinMode(BUZZER_PIN, OUTPUT);
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);

  Serial.println("Warming up the MQ-4 (2 min) in clean air...");
  delay(120000);
  cleanAirValue = analogRead(MQ4_PIN);
  Serial.print("Clean-air baseline: ");
  Serial.println(cleanAirValue);
}

void loop() {
  int reading = analogRead(MQ4_PIN);
  Serial.println(reading);

  if (reading > cleanAirValue + ALARM_MARGIN) {
    digitalWrite(LED_PIN, HIGH);      // combustible gas above baseline -> alarm
    digitalWrite(BUZZER_PIN, HIGH);
  } else {
    digitalWrite(LED_PIN, LOW);
    digitalWrite(BUZZER_PIN, LOW);
  }
  delay(500);
}
4

Warm up, baseline and test SAFELY

Power it in fresh air and let the 2-minute warm-up set the baseline (a new MQ-4 also needs a 24–48 h burn-in). Test with only a TINY controlled source in a well-ventilated room — a brief puff of gas from an UNLIT lighter held near the sensor. NEVER test with a real gas leak, a large amount of gas, or anywhere near a flame or spark. Adjust ALARM_MARGIN for sensitivity.

5

Safety limits

Methane is highly flammable and, in enough concentration, explosive. This circuit is a LEARNING project and at best a supplementary indicator — it is NOT a certified gas-leak detector: the hobby MQ-4 gives a relative reading, not calibrated ppm, drifts, and needs re-baselining. For real protection use a certified natural-gas detector, and if you ever smell gas, do not switch anything on or off — leave and call your gas utility.

Vifaa

8

Zana Zinazohitajika

1
Jumla inayokadiriwa
$56.00

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

Building a Carbon Monoxide Detectorna Ed
Building an Air-Quality Monitorna Ed

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Building a Carbon Monoxide Detectorelectronics
Building an Ultrasonic Parking Sensorelectronics
Building an Air-Quality Monitorelectronics
Building an Infrared Distance Sensorelectronics
Sewing a LilyPad LED Circuitelectronics
Blinking an LED with LilyPad Arduinoelectronics

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...