Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Camera Tripod: a Four-Fold Ash Tripod Stand (Hasluck, 1902)
Paul N. Hasluck (ed.) · Public domain (published 1902)
Woody

Imeundwa na

Woody

4. Novemba 2026NO
4
0
0
0
0

Camera Tripod: a Four-Fold Ash Tripod Stand (Hasluck, 1902)

A light, compact folding camera stand: three legs, each of seven ash laths riveted so it folds in four, locked open by brass buttons, on a triangular ash top with brass pins and a hole for the camera screw. Hasluck says the same method makes stands that fold in three or two. Source: Paul N. Hasluck, Photographic Cameras and Accessories (1902), pp. 153-157. Picture: Figs. 226-230 of the book.
Kati
Unknown

Maagizo

1

Cut the ash laths

Cut laths of good ash, true and square or the stand won't be rigid, and round the edges slightly: six 17 1/4 x 5/8 x 3/8 in, six 16 x 5/8 x 3/8 in, six 15 1/2 x 5/8 x 3/8 in, and three 14 x 5/8 x 5/8 in.

Vifaa kwa hatua hii:

Ubao wa mti wa ashUbao wa mti wa ash1 21 laths

Zana zinazohitajika:

Msumeno wa mgongoMsumeno wa mgongo
Randa ndogo ya kiganjaRanda ndogo ya kiganja
2

Fit the top ends and stretcher

On each 17 1/4 in lath let in flush a 1/16 in brass plate, 1 1/4 in long, with a 3/16 in hole 1/4 in from the top, held by two countersunk brass screws; bore the wood to match and take off the top corners. On one lath of each pair cut a groove inside, about 3/16 in deep and 3 1/2 in long, starting 2 in from the top, and hinge a 1/8 in brass rod stretcher in it on a pin. On the other lath cut a curved groove 1 1/2 in long, 3/16 in wide, with a small hole at the bottom where the rod catches.

Vifaa kwa hatua hii:

Bamba la Shaba ya NjanoBamba la Shaba ya Njano1 1/16 in plates
Parafujo za mbaoParafujo za mbao1 small brass screws
Ufito wa shaba ya njanoUfito wa shaba ya njano1 1/8 in stretcher

Zana zinazohitajika:

Fremu ya msumeno wa chuma na mabapaFremu ya msumeno wa chuma na mabapa
Tupa ya chumaTupa ya chuma
Kekee cha mkonoKekee cha mkono
PatasiPatasi
Bisibisi bapaBisibisi bapa
3

Bore and rivet the legs

Bore the rivet holes: in the long laths 1 3/4 in from the lower end, counterbored so the copper rivet head sits flush, then 1/8 in through; in the 16 in and 15 1/2 in laths 1/2 in and 1 3/4 in from the ends; in each 14 in piece 1/2 in from one end, and taper its other end for a pointed iron shoe or a steel point and ferrule. Rivet the 21 laths into three legs with 1/8 in copper rivets and washers: a 16 in lath inside each 17 1/4 in one, a 15 1/2 in lath inside that, the 14 in foot between the last pair. Rivets flush, just tight enough to fold but not loose.

Vifaa kwa hatua hii:

Rivet za shabaRivet za shaba1 1/8 in, with washers
Metali isiyojulikanaMetali isiyojulikana3 iron shoes or steel points

Zana zinazohitajika:

Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kekee cha mkonoKekee cha mkono
Nyundo ya rivetiNyundo ya riveti
4

Add cross strips and lock buttons

Screw 1/16 in brass strips across the bottom ends of each pair of laths (Fig. 229). Under them screw strips carrying a small brass button riveted at the centre; turned, the button hooks over the strip above and locks the joint open (Fig. 230).

Vifaa kwa hatua hii:

Bamba la Shaba ya NjanoBamba la Shaba ya Njano1 cross strips, buttons
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Fremu ya msumeno wa chuma na mabapaFremu ya msumeno wa chuma na mabapa
Tupa ya chumaTupa ya chuma
Bisibisi bapaBisibisi bapa
Nyundo ya rivetiNyundo ya riveti
5

Make the top

Plane ash to 1/2 in and draw an equilateral triangle with 8 1/2 in sides. Bisect the angles; 2 in from each corner draw a line at right angles, go 1/2 in in along the sides, and mark three rectangles 2 7/8 x 3/4 in; cut the outline (Fig. 231). Fix a 3/16 in brass rod, one end tapered, across each rectangle, bored 3/8 in from the outer edge and projecting about 1/2 in, for the legs to hang on. Bore a 1/4 in hole in the centre for the camera screw and glue felt on top.

Vifaa kwa hatua hii:

Ubao wa mti wa ashUbao wa mti wa ash1 top
Ufito wa shaba ya njanoUfito wa shaba ya njano3 3/16 in pins
Kitambaa cha sufu kilichoshindiliwaKitambaa cha sufu kilichoshindiliwa1 kipande
Gundi ya wanyamaGundi ya wanyama1 kipande

Zana zinazohitajika:

Randa ndogo ya kiganjaRanda ndogo ya kiganja
Msumeno wa mgongoMsumeno wa mgongo
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Kekee cha mkonoKekee cha mkono
6

Finish

Glasspaper and varnish the wood, and lacquer the brass.

Vifaa kwa hatua hii:

Vanishi ya shelakiVanishi ya shelaki1 varnish
Nyenzo isiyojulikanaNyenzo isiyojulikana1 brass lacquer

Zana zinazohitajika:

Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)

Vifaa

10

Zana Zinazohitajika

10

Mchoro huu unatengeneza

Thumbnail
Kishikilia nafasi

Tripodi ya kamera

Free

172
0

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...