Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge

Imeundwa na

Forge

13. Novemba 2026NO
0
0
0
0
0

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)

Ferdinand H. Dalrymple of Bedford, Ohio, received US 2,163,315, dated 20 June 1939, for a shaft collar "comprised of few parts which are readily obtainable as standard market articles". Two washers are held apart by nuts welded between them. The nuts' inner faces rest on the shaft, and a set screw in one nut's thread holds it. It needs no machining. He says it is stronger, lighter and cheaper than a cast collar, and breaks less readily under a hammer. It also touches the shaft only along lines, so it rusts to it less, and oil can be put in between the nuts. The patent gives no sizes for this form; every size here is ours.
Mwanzo
About 1 hour

Maagizo

1

Will it fit together?

Inapakia daftari la Jupyter…
2

Read US 2,163,315

"Preferably, I use as plates standard washers of suitable dimension, and I use as blocks standard nuts." "Inasmuch as the space between the plates is not sufficient for the convenient manipulation of an ordinary wrench, I use socketed set screws for securing the collar to the shaft."
3

Set the parts up on a bar

Use plain steel washers and nuts, not zinc-plated ones. Wire-brush them clean. Grip a 16 mm round bar upright in the vice. Slide one washer onto it, stand four M8 nuts on the washer round the bar at quarter turns, each with a flat down and its hole pointing at the bar's centre and its inner face against the bar. Put the second washer on top and squeeze the stack with the C-clamp; check with the square that the washers are parallel.

Vifaa kwa hatua hii:

Washa bapaWasha bapa2 vipande
Nati ya pembe sitaNati ya pembe sita4 vipande

Zana zinazohitajika:

Ufito mviringo wa chuma lainiUfito mviringo wa chuma laini
Kibano cha meza ya kaziKibano cha meza ya kazi
Klampu ya umbo la CKlampu ya umbo la C
Seti ya brashi za wayaSeti ya brashi za waya
Skwea ya mchanganyikoSkwea ya mchanganyiko
Kipima-unene cha dijitali cha inchi 6Kipima-unene cha dijitali cha inchi 6
4

Weld the nuts to the washers

Wearing the helmet and gloves, tack each nut to both washers with a short fillet weld at its outer corner, keeping the arc away from the bar. Let it cool, lift the collar off the bar, and run a fillet along both ends of every nut on both washers. Chip and wire-brush the slag. Run the set screw in and out of one nut to clear any spatter from its thread, and file the bore ends smooth.

Vifaa kwa hatua hii:

Elektrodi ya kulehemuElektrodi ya kulehemu4 vipande

Zana zinazohitajika:

Mashine ya kulehemu kwa upindeMashine ya kulehemu kwa upinde
Kofia ya kulehemu inayotia giza yenyeweKofia ya kulehemu inayotia giza yenyewe
Glavu za kulehemuGlavu za kulehemu
Seti ya brashi za wayaSeti ya brashi za waya
Kisaga cha pembeKisaga cha pembe
Seti ya tupaSeti ya tupa
Miwani ya usalamaMiwani ya usalama
5

The collar in 3D

FreeCAD model, our sizes: the two 50 mm washers, the four M8 nuts between them at quarter turns, their inner faces on a 16 mm shaft, and the socket set screw in one nut. The welds are not modelled.
Faili ya UsanifuSTLCC0 - Free
6

Fit it on the shaft

Run an M8 x 8 cup point socket set screw into one nut from outside. Slide the collar onto the shaft to its place and tighten the screw with the hex key between the washers. Try to slide and turn it; it must not move.

Vifaa kwa hatua hii:

Skrubu ya kubana yenye ncha ya kikombeSkrubu ya kubana yenye ncha ya kikombe1 kipande

Zana zinazohitajika:

Seti ya funguo za pembe sitaSeti ya funguo za pembe sita
7

Troubleshooting

Built-up collar troubleshooting.

Flow

Loading...
8

History and honest limits

**Ferdinand H. Dalrymple** of Bedford, Ohio, US 2,163,315, dated 20 June 1939, filed 2 November 1937. He claimed "opposed spaced plane plates formed with coaxial bores for the reception of a shaft, transverse spaced internally-threaded blocks welded to the opposed faces of the plates and serving as the sole means for holding the plates in relatively fixed positions, and set screws engaging the blocks". His Figs. 8 and 9 use standard square nuts and socketed set screws; we use hex nuts, as his Figs. 1-5 allow "standard nuts". His patent also shows special blocks, flanged plates, three-plate and split forms; we build the simplest. He gives no sizes for this form; every size here is ours.

Vifaa

4

Zana Zinazohitajika

13

Faili za muundo

1
  • dalrymple-washer-and-nut-built-up-shaft-collar.stlSTLCC0

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...