Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Digital Oscilloscope: Waveform Stored in Memory and Shown on a CRT (Schumann, Nicolet, US 3,816,815, 1974)
An oscilloscope with a memory. After a trigger, an analog-to-digital converter measures the input at regular intervals and writes each reading into its own memory register, replacing the old one. The screen then shows the memory: each register's number sets the beam's height, its address sets the beam's place across. The last waveform can be held on the screen as long as you like.
Result: a digital storage oscilloscope with 4,096 points of 12 bits, refresh and hold modes and single-shot capture.
Source: R. W. Schumann (Nicolet), US 3,816,815 (1974). Unknown: sample rate, bandwidth, voltages and the parts used. Picture: the patent drawing.
Mtaalamu
Unknown
Maagizo
1
1
Sample and convert the input
Sample and convert the input
Bring the analog input to an analog-to-digital converter, through a BNC socket. A sampling oscillator, divided by four by two flip-flops so the first reading comes soon after the sweep starts, fires a one-shot multivibrator that gives the converter its measure command. The converter holds each 12-bit result on its output lines and signals the end of each conversion. Ours: a BNC socket. Not given: the sample rate.
Vifaa kwa hatua hii:
Kigeuzi cha Analogi kuwa Dijitali1 12-bit converter
Osileta ya saa1 sampling oscillator
Mchanganyiko wa IC za mantiki1 flip-flops, one-shots, gates
Seti ya viunganishi vya koaksia (BNC / SO-239)1 input socketZana zinazohitajika:
Chuma cha kulehemia
Koleo la kumenya waya2
2
Store each reading in memory
Store each reading in memory
Wire an integrated-circuit memory of 4,096 registers, 12 bits each, that can be read without changing it. A 12-bit address counter picks the register. On each write command the register at the current address takes the last reading from the converter, and the counter steps on. When the sweep starts, a one-shot resets the counter to zero. When it reaches the last address, its last-address signal ends the sweep.
Vifaa kwa hatua hii:
Kumbukumbu ya saketi jumuishi1 4,096 x 12-bit storeZana zinazohitajika:
Chuma cha kulehemiaKoleo la kumenya waya3
3
Drive the CRT from the memory
Drive the CRT from the memory
Feed the addressed register's number to one digital-to-analog converter and the address to a second. Their outputs drive the vertical and horizontal deflection plates of a cathode-ray tube, so the beam always stands at the height of the stored reading and at the place of its address. Wire the sweep line to the tube's intensifier, to brighten the trace while a waveform is being taken.
Vifaa kwa hatua hii:
Kigeuzi cha dijitali hadi analogi2 vertical and horizontal
Neli ya miale ya kathodi1 display tubeZana zinazohitajika:
Chuma cha kulehemiaKoleo la kumenya waya4
4
Wire the trigger and the modes
Wire the trigger and the modes
A trigger input, usually from the leading edge of the input waveform, starts the sweep, once a measure flip-flop has armed it. Put a two-position mode switch on the face: MODE I and MODE II. Add a push button in the probe, a switch on the panel and an external initiate input; each goes through a flip-flop that removes contact bounce. Two more oscillators step the memory round to refresh the display between waveforms. Mount it all in a case with its supply. Ours: toggle switches, an aluminium case, a DC supply. Not given: the supply voltages.
Vifaa kwa hatua hii:
Osileta ya saa2 display sequencing oscillators
Swichi ya mpini2 mode and panel switches
Kitufe cha kubonyeza1 probe switch
Sanduku la alumini1 caseZana zinazohitajika:
Chanzo cha nishati ya mkondo wa moja kwa moja
Kekee cha NguzoChuma cha kulehemia5
5
Capture and hold a waveform
Capture and hold a waveform
In MODE I, refresh: each new triggered waveform replaces the last on the screen. Press the probe or panel switch to hold: new waveforms are rejected and the last one stays on the screen. In MODE II the screen normally holds; on command, it takes the first waveform after the command, stores it and shows it steadily. Test it with a known signal.
Zana zinazohitajika:
Kizalisha MawimbiVifaa
10- 1 12-bit converterKishikilia Nafasi
- 2 display sequencing oscillatorsKishikilia Nafasi
- 1 flip-flops, one-shots, gatesKishikilia Nafasi
- 1 input socketKishikilia Nafasi
- 1 4,096 x 12-bit storeKishikilia Nafasi
- 2 vertical and horizontalKishikilia Nafasi
- 1 display tubeKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 1 caseKishikilia Nafasi
Zana Zinazohitajika
5- 2 vendors sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.