SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Double-Swing Churn: Swing the Platform, the Toothed Pieces Work Both Dashers
Daniel Osgood, Jr., Bluehill, Maine · Public domain (expired patent)
Woody

Imeundwa na

Woody

6. Oktoba 2026NO
34
0
0
0
0

Double-Swing Churn: Swing the Platform, the Toothed Pieces Work Both Dashers

Working a dash churn means lifting the dasher, again and again. Daniel Osgood, Jr., of Bluehill, Maine, received US 831, dated 9 July 1838, for what he called "Osgood's Double-Swing Churn": two common churns on a platform swinging in a frame. The side pieces rising from the platform are cut into teeth that mesh with the teeth of two pieces hung above, so as the platform swings backward and forward a lever is alternately raised and depressed, "giving the downward and upward motion to the dashers." The power required, he wrote, "is nearly in proportion to the power required to draw a pendulum in its lateral motion compared with that of raising its weight." This rung compares the swing of his platform and ours, then prints the toothed sectors, builds a tabletop frame for two jars, and makes butter.
Kati
About 6 hours, plus printing

Maagizo

1

Swing period and dasher stroke

Inapakia daftari la Jupyter…
2

One load balancing another on a lever

The embedded blueprint lifts water with a counterweighted beam. Osgood's beam balances one churn's dasher against the other's, and he says to balance a single churn with a weight.
3

Read US 831

"This saving of labor is acquired by placing two common churns, Figure 3 (a a) on a swinging platform (b). This platform is made to swing by being suspended in the frame A, B, C, D, by a rod passing through the frame and two pieces (d d) rising from the sides of the platform (b)... The ends of the side pieces (d, d,) and the corresponding upper, pieces (g, g,) are cut into teeth or cogs (l l,) and mesh into each other."
4

Print four toothed sectors

Print four identical sectors (/uploads/blueprints/double-swing-churn-sector.stl), flat. Each has a 6.6 mm pivot hole at the centre of its teeth and two screw holes in its tail. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Vifaa kwa hatua hii:

Uzi wa PETGUzi wa PETG1 kipande

Zana zinazohitajika:

Printa ya 3D ya nyuzi (FDM)Printa ya 3D ya nyuzi (FDM)
5

Build the frame and platform

Make two A-frames of pine about 420 mm tall, joined at the top by a cross bar. Drill both for two 6 mm steel rods 60 mm apart, one above the other: the lower rod carries the platform and the upper carries the beam. Cut a plywood platform 280 × 130 mm. Screw an upright pine strip to each side of the platform, reaching up to the lower rod, and screw a sector to the top of each strip, teeth up and pivot on the rod.

Vifaa kwa hatua hii:

Ubao wa msonobariUbao wa msonobari1 kipande
Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Ufito wa chuma lainiUfito wa chuma laini1 kipande
Skrubu ya mti #8 x inchi 1Skrubu ya mti #8 x inchi 11 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Msumeno wa chumaMsumeno wa chuma
Kekee cha BetriKekee cha Betri
Seti ya vichimbuziSeti ya vichimbuzi
VibanoVibano
Tepi ya kupimiaTepi ya kupimia
6

Hang the beam and dashers

Screw the other two sectors to two short pine pieces hung on the upper rod, teeth down, meshing with the lower ones. Join the hung pieces with a cross bar and fix a beam across it at right angles, 200 mm long. Hang a dowel dasher with a plywood disc from each end on a loose screw, through a hole in each jar's lid. Fit a long handle to the platform.

Vifaa kwa hatua hii:

Ubao wa msonobariUbao wa msonobari1 kipande
Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Chupa ya KiooChupa ya Kioo2 vipande
Skrubu ya mti #8 x inchi 1Skrubu ya mti #8 x inchi 11 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha BetriKekee cha Betri
Seti ya vichimbuziSeti ya vichimbuzi
Seti ya bisibisiSeti ya bisibisi
7

The patent drawing

US 831 drawing sheet, public domain (expired patent).
Hatua 7 - Image 1
8

Swing and make butter

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour half into each jar, no more than a third full, and fit the lids. Swing the platform steadily by the handle; the dashers rise and fall in turn. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.

Vifaa kwa hatua hii:

Malai nzitoMalai nzito500 ml
Chumvi ya Bahari MbichiChumvi ya Bahari Mbichi1 kipande
MajiMaji1 kipande

Zana zinazohitajika:

Kipima joto chenye kijiti kinachobaki ndaniKipima joto chenye kijiti kinachobaki ndani
Saa ya kupima mudaSaa ya kupima muda
Mizani ya dijitali ya jikoniMizani ya dijitali ya jikoni
Bakuli kubwa la kuchanganyia la chuma cha puaBakuli kubwa la kuchanganyia la chuma cha pua
9

Teeth that slip, a swing that dies

Double-swing churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Daniel Osgood, Jr.** of Bluehill, Hancock County, Maine, received US 831, dated 9 July 1838. He gave the dimensions for common use: a frame 3 ft 1 in high, churns 1 ft 7 in high, 14 inches across at the bottom and 12 at the top, a platform 2 ft 6 in by 1 ft, and the pendulum 1 ft 4 in from its rod to the platform. "When but one churn is necessary, the other may be dispensed with by substituting any other weight in its stead to balance the one that is used." He claimed "the manner in which the dashers are worked by the pendulous motion of the churn." **Honest limits.** Jars on a tabletop frame stand in for his two churns, and printed sectors for his wooden teeth. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.

Vifaa

11

Zana Zinazohitajika

12

Mchoro huu unatengeneza

Thumbnail
Kishikilia nafasi

Chombo cha kusukia siagi

Free

19
0

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

Rocking-Stool Churn: Rock the Churn, the Dashers Ride With It

Rocking-Stool Churn: Rock the Churn, the Dashers Ride With It

na YourGrandmaIS

CHAKULA NA VINYWAJI

27
0
0
0
0
0
Building a Shaduf Irrigation Lever — Counterweighted Water Lift

Building a Shaduf Irrigation Lever — Counterweighted Water Lift

na EmmaSE

Majini

133
0
0
0
2
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation

Churning Butter from Cream — The 5,000-Year-Old Fat Separation

na TheChefDK

UJANJA

50
0
0
0
0
0

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...