Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
Kati
Two to three days of building
Maagizo
1
1
His sizes
His sizes
Inapakia daftari la Jupyter…
2
2
Read Edwinson
Read Edwinson
"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3
3
Build the base
Build the base
Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.
Vifaa kwa hatua hii:
Bonge la jiwe1 kipande
Pete ya chuma1 kipande
Udongo Unaostahimili Moto1 kipandeZana zinazohitajika:
Mwiko wa mwashi
Rulani ya Maji4
4
Make the fire back and tuyere
Make the fire back and tuyere
Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)
Vifaa kwa hatua hii:
Chembe za chuma (uzito wa kusawazisha)1 kipande
Bamba la chuma1 kipande
Mkusanyiko wa bolti za pembe sita1 kipandeZana zinazohitajika:
Kekee cha Nguzo
Fua ya mhunzi
Nyundo5
5
Firebrick top and back
Firebrick top and back
Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).
Vifaa kwa hatua hii:
Matofali yanayostahimili moto1 kipande
Udongo Unaostahimili Moto1 kipande
Pete ya chuma1 kipandeZana zinazohitajika:
Mwiko wa mwashi
Rulani ya Maji6
6
Fit the slake trough
Fit the slake trough
Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.
Vifaa kwa hatua hii:
Bati la Chuma Laini1 kipande
Rivet za chuma1 kipande
Maji1 kipandeZana zinazohitajika:
Kekee cha Nguzo
Nyundo7
7
Bind with the rim
Bind with the rim
Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.
Vifaa kwa hatua hii:
Bamba la chuma1 kipande
Mkusanyiko wa bolti za pembe sita1 kipandeZana zinazohitajika:
Fua ya mhunzi
Fuawe
Nyundo
Kekee cha Nguzo8
8
Connect the blast
Connect the blast
Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.
Zana zinazohitajika:
Kipuliza hewa9
9
Lay the floor
Lay the floor
Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.
Vifaa kwa hatua hii:
Saruji ya Portland1 kipande
Maji1 kipandeZana zinazohitajika:
Nyundo10
10
Troubleshooting
Troubleshooting
Hearth troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.
Vifaa
11- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- Kishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

