Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
9
0
0
0
0

Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)

George Edwinson's tong-making lesson from Amateur Work (1886): jaws forged from inch-square iron, reins of 5/8 in. rod scarfed and welded on, the halves riveted with a hot iron pin. The same flat-bit tongs are then reshaped into pincer, hammer and crook-bit tongs, light smith's pliers, and thinned and curved into crucible tongs.
Juu
A day at the forge

Maagizo

1

His sizes

Inapakia daftari la Jupyter…
2

Read Edwinson

"Indeed, the man who can turn out a good pair of tongs may be trusted with almost any job in the smithy."
3

Forge the reins

Cut two pieces of 5/8 in. (16 mm) iron rod, each 2 ft (0.6 m) long, with a cold chisel. Bring one end of each to a white welding heat and draw 3-4 in. down to a taper from 5/8 to 1/2 in., rounded for the hand. Upset the other ends at a white heat and scarf them (his figs. 27-28).

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Patasi ya chuma baridiPatasi ya chuma baridi
Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
4

Forge the jaws

Cut two 6 in. pieces of 1 in. square iron (or one 12 in. bar, worked from each end before cutting, fig. 29). Forge each jaw end 4 in. long, 1 1/4 in. wide and 3/8 in. thick. Flatten the other end to 1/4 in. thick, round it for the joint (fig. 30) and draw it to a slightly rounded taper (fig. 31).

Vifaa kwa hatua hii:

Fimbo ya mraba ya chuma lainiFimbo ya mraba ya chuma laini1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
5

Punch the joint

Mark the hole with a centre punch, heat, and punch a 3/8 in. hole over the anvil's heel hole with an iron punch tapering 1/4 to 1/2 in. (fig. 35), or a steel punch of 5/8 in. tool steel.

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Kigwe cha KatikatiKigwe cha Katikati
Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
6

Weld jaw to rein

Scarf the taper end of each jaw to fit a rein. Heat both to a welding heat in a clear fire, throw on clean fine fresh-water sand and heat until pasty. Tap the scarfs together lightly, return to the fire a moment, and finish the weld. At a red heat forge the square part to blend into the round rein (fig. 32).

Vifaa kwa hatua hii:

MchangaMchanga1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
7

Rivet the joint

Smiths' way: nick a 3/8 in. round iron rod to rivet length, put the halves together, insert the hot end, twist it off, let 1/4 in. stand below, and rivet both sides. (Or make a 3/4 x 3/8 in. button-headed rivet in a 3/8 in. hole in a flat iron.) If the joint locks, reheat jaws and pin to bright red and work them free.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Kibamba cha kutengeneza vichwa vya misumariKibamba cha kutengeneza vichwa vya misumari
8

Set the jaws

Heat the jaws and set them to the width of the stock to be held. Spring them wider with a piece of cold iron between and a few light blows.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
9

Crucible tongs and other forms

From flat-bit tongs at the fig. 32 stage: lengthen and curve the bits for pincer tongs (angular notches hold round or square bars), more for hammer tongs, bend them sideways for crook-bit tongs. Small flat-bit tongs with lengthened, shaped bits are smith's pliers; thin those out further and curve them like pincers to make crucible tongs for hot crucibles and pots of molten metal. Heavy tongs 2-5 ft long need stouter iron.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
10

Troubleshooting

Tongs troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" III, **Amateur Work, Illustrated**, vol. V (1886), pp. 266-269 (checked on the archive.org scan amateurworkillus05lond). He gives full sizes only for the flat-bit tongs; crucible tong sizes and curvature are left to the work. Metric figures and tools are ours.

Vifaa

4

Zana Zinazohitajika

7

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...