Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
9
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
Juu
A day at the forge

Maagizo

1

His weights

Inapakia daftari la Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

Vifaa kwa hatua hii:

Feleji ya kalibuFeleji ya kalibu1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo kubwaNyundo kubwa
Koleo za mhunziKoleo za mhunzi
Kipanua tundu cha mhunziKipanua tundu cha mhunzi
Ndoo ya kupoza chumaNdoo ya kupoza chuma
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande
Nondo za chuma chenye malengelengeNondo za chuma chenye malengelenge1 kipande
Poda ya boraksiPoda ya boraksi1 kipande
MchangaMchanga1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Patasi ya motoPatasi ya moto
FuaweFuawe
Nyundo kubwaNyundo kubwa
Koleo za mhunziKoleo za mhunzi
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Kipanua tundu cha mhunziKipanua tundu cha mhunzi
Patasi ya motoPatasi ya moto
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Kipanua tundu cha mhunziKipanua tundu cha mhunzi
FuaweFuawe
NyundoNyundo
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

Zana zinazohitajika:

FuaweFuawe
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

Vifaa kwa hatua hii:

Kipande cha mti wa ashKipande cha mti wa ash1 kipande
Vibanzi vya mbaoVibanzi vya mbao1 kipande

Zana zinazohitajika:

Kisu cha KuvutaKisu cha Kuvuta
PatasiPatasi
NyundoNyundo
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

Vifaa

7

Zana Zinazohitajika

10

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...