Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
6
0
0
0
0

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)

Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
Juu
A day at the forge per pair

Maagizo

1

Read Edwinson

"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2

Weld the blanks

As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande
Feleji ya kalibuFeleji ya kalibu1 kipande
Poda ya boraksiPoda ya boraksi1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo kubwaNyundo kubwa
Patasi ya motoPatasi ya moto
Koleo za mhunziKoleo za mhunzi
3

Bottom swage

Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
4

Top swage

Forge the matching top tool with a neck for its handle.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
5

Cut the grooves

Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Fuller (chombo cha kuchora mifereji)Fuller (chombo cha kuchora mifereji)
FuaweFuawe
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
6

Handle or spring

Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).

Vifaa kwa hatua hii:

Fimbo za hazel (mbichi, zinazoinama)Fimbo za hazel (mbichi, zinazoinama)1 kipande
Ufito mviringo wa chuma lainiUfito mviringo wa chuma laini1 kipande
Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 kipande
Utepe wa chuma cha springiUtepe wa chuma cha springi1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
7

Grind and harden

Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).

Zana zinazohitajika:

Jiwe la kunoa la gurudumuJiwe la kunoa la gurudumu
Fua ya mhunziFua ya mhunzi
Ndoo ya kupoza chumaNdoo ya kupoza chuma
8

Use them

Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Nyundo kubwaNyundo kubwa
Kipima uneneKipima unene
9

Troubleshooting

Swage troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.

Vifaa

7

Zana Zinazohitajika

11

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...