Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Whitworth Taps from Cast Tool Steel: Turned, Chased, Fluted and Hardened in Salt Water, with Their Wrench (Edwinson, 1886)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
10
0
0
0
0

Whitworth Taps from Cast Tool Steel: Turned, Chased, Fluted and Hardened in Salt Water, with Their Wrench (Edwinson, 1886)

George Edwinson's instructions (Amateur Work, 1886) for a home-made set of Whitworth taps, 3/16 to 1 inch, in entry, half-plug and full-plug form: cast tool steel annealed, turned, roughed with a single-point tool and finished with home-made chasers in a screw-cutting lathe, fluted, hardened in swirled salt water and tempered deep yellow; plus the two-hole tap wrench. The dies and stock are in the companion blueprint.
Juu
Several days for a set of thirty

Maagizo

1

His tables

Inapakia daftari la Jupyter…
2

Read Edwinson

"There is only one perfect method of making a good tap, and that is by turning the metal ... and cutting the thread in a screw-cutting lathe."
3

Cut and anneal the blanks

Cut the best 1 in. square cast tool steel into 3 1/2 in. lengths for the large taps, and 1/2 in. steel into 3 in. lengths for the small ones (a full set takes 5 ft 6 in. of the first and 3 ft of the second). Anneal: blood red, cooled slowly in hot ashes. File the ends square, centre-punch, and drill the centres 1/16 in. (small) or 1/8 in. (large) deep.

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Patasi ya motoPatasi ya moto
Fua ya mhunziFua ya mhunzi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kigwe cha KatikatiKigwe cha Katikati
Kekee cha NguzoKekee cha Nguzo
4

Rough out the taps

Turn the corners off. Mark each tap: entry 1/2 in. head, 3/4 in. shank; half plug 1/2 in. head, 1 in. shank; full plug 1/2 in. head, 1 1/4 in. shank; the rest is thread (for the 1 in. set; 7/8 the same, smaller sets in proportion with shanks turned down for clearance). Below 1/2 in. make the square heads 3/8 or 3/16 in. to fit the wrench. Anneal again, turn true and smooth, and finish with a fine file.

Zana zinazohitajika:

Kereza ya ChumaKereza ya Chuma
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Fua ya mhunziFua ya mhunzi
5

Make the chasers

From flat tool steel forge one chaser per size, the largest 1 in. wide, 1/4 in. thick and 5 in. long, the rest a little smaller, with 3 1/2 or 4 1/2 teeth across the width and a tang for a wooden handle (fig. 72). Upset the point, grind, anneal, file the teeth, and finish them by running the chaser against a full plug tap or hub of that pitch in the lathe. Inside chasers: against a left-handed hub, or file off the lower leading edge of each tooth (fig. 74).

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kereza ya ChumaKereza ya Chuma
6

Cut the threads

Rough each thread with a single fine-point tool in the slide rest of a screw-cutting lathe, set with the change wheels for its pitch (notebook), then finish with the chaser. Whitworth form: 55 degree angle, one-sixth rounded off top and bottom. Stamp each tap with its size and threads per inch.

Zana zinazohitajika:

Kereza ya ChumaKereza ya Chuma
NyundoNyundo
7

Flute and point

Cut three flutes along each tap with a circular cutter in the lathe or a thin emery wheel (before hardening), or grind the sides flat (fig. 75). Grind fully 1/2 in. of each entry tap to a taper and the first few threads of the half plug; leave the full plug entire.

Zana zinazohitajika:

Kereza ya ChumaKereza ya Chuma
Kisagia cha mezaKisagia cha meza
8

Harden and temper

Heat each tap or chaser to blood red and plunge it straight down into a pail of water with a handful of common salt, swirled with a stick, into the middle of the swirl so it does not warp. Rub part bright, lay it in angle or grooved iron over a clear fire or a Bunsen burner until the bright part is deep yellow, then dip it in cold water. Grind the chaser tops level.

Vifaa kwa hatua hii:

ChumviChumvi1 kipande
MajiMaji1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
NdooNdoo
Kichomeo cha BunsenKichomeo cha Bunsen
Kisagia cha mezaKisagia cha meza
9

Make the tap wrench

Take 10 in. of 3/4 in. round steel or iron. Heat the middle, upset it and flatten 2 1/2 in. to 1/2 in. thick. Drill two small holes and open them with a square punch, one to 3/8 in. and one to 1/4 in. Straighten, anneal, centre the ends and turn them in the lathe, then harden and temper. A longer, heavier wrench with one 1/2 in. hole suits the big taps.

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo kubwaNyundo kubwa
Kekee cha NguzoKekee cha Nguzo
Kereza ya ChumaKereza ya Chuma
10

Troubleshooting

Tap troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" V, **Amateur Work, Illustrated**, vol. V (1886), pp. 434-438 and figs. 71-77 (checked on the archive.org scan amateurworkillus05lond). He himself advised buying Whitworth gear rather than making it. Metric conversions and the tools listed are ours.

Vifaa

3
  • Kishikilia Nafasi
  • 1 kipande
    Kishikilia Nafasi
  • 1 kipande
    Kishikilia Nafasi

Zana Zinazohitajika

12

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...