Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
8
0
0
0
0

New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)

Martin Folkush of Milwaukee received US 1,374,644, dated 12 April 1921, for a noisemaker "that can be heard for a great distance". Hold the handle and swing the box round it: two thin wooden tongues inside snap over the posts of a fixed bobbin, one in single clacks and one in double, and the box rings like a sounding board. A slider changes the pitch. We make it from plywood, dowel and hardwood strip. All sizes are ours.
Kati
About 4 hours

Maagizo

1

Posts on the bobbin

Inapakia daftari la Jupyter…
2

Read US 1,374,644

"Upon rotating the casing 12 upon the shaft 11, the sounding boards 21 and 22 will be brought into violent engagement with the posts 19 and 20 causing loud sounds to be emitted."
3

Make the handle and shaft

Shape a handle from hardwood handle stock with a rasp, his handle 10, and glue a dowel shaft 11 into its end.

Vifaa kwa hatua hii:

Mti Mgumu wa Kutengenezea MipiniMti Mgumu wa Kutengenezea Mipini1 kipande
Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Tupa mbovu ya mbaoTupa mbovu ya mbao
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)
Kekee cha mkonoKekee cha mkono
4

Make the bobbin

Cut three plywood disks 60 mm across (ours): two ends and the middle disk 18. Drill all three on the circle from the notebook and glue dowel posts 19 through all of them; then glue the shorter posts 20 between the middle disk and one end disk only, between the long ones. Drill the centre for the shaft and pin the bobbin to it, his pin 17.

Vifaa kwa hatua hii:

Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
Bikari ya ncha mbiliBikari ya ncha mbili
Kekee cha mkonoKekee cha mkono
Msumeno wa mkonoMsumeno wa mkono
5

Make the casing

Cut two plywood sides 14 with a round head 13 at one end, bored for the shaft. Join them with a closed end 24 and an open frame so the bobbin turns freely between the heads. Glue a cross rib 23 inside the closed end. Cut a slot 28 in each side for the slider.

Vifaa kwa hatua hii:

Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
Kekee cha mkonoKekee cha mkono
6

Fit the sounding boards

Cut two thin hardwood strips (his sounding boards 21 and 22) long enough to reach from the rib to just inside the circle of posts, and screw their ends to the rib, side by side, one opposite each half of the bobbin.

Vifaa kwa hatua hii:

Utepe wa mbao gumuUtepe wa mbao gumu1 kipande
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkonoKekee cha mkono
Seti ya bisibisiSeti ya bisibisi
7

Fit the slider and close the box

Make a small wooden slider 26 that surrounds both boards, with a length of threaded rod through it whose ends pass out through the slots; put a wing nut on each end (his set nuts 29). Put the casing on the shaft over the bobbin and close the other side with a plywood plate 25, making a resonant box.

Vifaa kwa hatua hii:

Utepe wa mbao gumuUtepe wa mbao gumu1 kipande
Fimbo yenye nyuziFimbo yenye nyuzi1 kipande
Nati ya mabawaNati ya mabawa2 vipande
Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkonoKekee cha mkono
Msumeno wa chumaMsumeno wa chuma
8

Play it

Hold the handle and swing the box round the shaft: the boards snap over the posts. Slide the slider toward the bobbin for a higher, sharper sound, away for a deeper one, and lock it with the wing nuts.
9

Troubleshooting

Noisemaker troubleshooting.

Flow

Loading...
10

History and honest limits

**Martin Folkush** of Milwaukee, US 1,374,644, dated 12 April 1921, filed 10 April 1920. He claimed "a noise maker comprising a shaft, a casing journaled thereon, a frame having spaced end supported posts", "one half of said frame being provided with double the number of posts that the other half has", and the pitch-adjusting slider. He names no materials and gives no sizes: the wood, all sizes, wing nuts and threaded rod are ours.

Vifaa

9

Zana Zinazohitajika

8

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...