Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
10
0
0
0
0

Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)

How the common English screw auger was made, from Holtzapffel's Turning and Mechanical Manipulation: a parallel steel blade twisted red-hot, a worm at the point to pull it into the wood, two lips sharpened to cut, and the shaft end forged into an eye for a tightly driven cross handle.
Juu
A day at the forge

Maagizo

1

Twist count

Inapakia daftari la Jupyter…
2

Read Holtzapffel

"The ordinary screw auger ... is forged as a parallel blade of steel ... it is twisted red-hot."
3

Forge the blade

Draw a steel bar out into a flat, parallel blade, leaving a round end for the shaft. Width, thickness and length are ours: make the blade as wide as the hole you want.

Vifaa kwa hatua hii:

Fito ya chuma cha zanaFito ya chuma cha zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
Fuller (chombo cha kuchora mifereji)Fuller (chombo cha kuchora mifereji)
4

Twist it red-hot

Heat the blade to red, grip one end in the vice and twist the other with a wrench into an even double spiral. Twist in short heats and keep the pitch even.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Kibano cha meza ya kaziKibano cha meza ya kazi
Mpini wa kukata nyuzi za ndaniMpini wa kukata nyuzi za ndani
Koleo za mhunziKoleo za mhunzi
5

Form the worm and lips

File the point into a worm (a small tapered screw, as on a gimlet) that pulls the auger into the work. Shape and sharpen the two corners, or lips, to cut at the very ends and a little up the sides.

Zana zinazohitajika:

Kibano cha meza ya kaziKibano cha meza ya kazi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
6

Forge the eye

Forge the top of the shaft into a ring or eye.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
NyundoNyundo
Koleo za mhunziKoleo za mhunzi
7

Harden and temper (ours)

He gives no hardening. Ours: harden the cutting end and temper it as for other wood-cutting edge tools, then hone the lips.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Ndoo ya kupoza chumaNdoo ya kupoza chuma
Jiwe la kunoaJiwe la kunoa
8

Fit the cross handle

Shape a hardwood bar and drive it tightly through the eye as a transverse handle.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande

Zana zinazohitajika:

Kisu cha KuvutaKisu cha Kuvuta
NyundoNyundo
9

Troubleshooting

Screw auger troubleshooting.

Flow

Loading...
10

History and honest limits

From Charles Holtzapffel, **Turning and Mechanical Manipulation**, vol. II (1846), pp. 540, 543 and 545-546 (checked on the archive.org scan turningmechanica02holtuoft). He also describes the single-lip auger: a half-round bar coiled into an open spiral with the flat side outwards, the end shaped like a shell auger. He gives no sizes or heat treatment: those, the tools and the handle wood are ours.

Vifaa

2

Zana Zinazohitajika

11

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...