SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
BAADAYE YA KIJANI
REVERSE ENGINEERING
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Making a LilyPad Night-Light
Ed

Imeundwa na

Ed

13. Julai 2026FI
1
0
0
0
0

Making a LilyPad Night-Light

Give your fabric a sense of sight. A LilyPad light sensor tells the microcontroller how bright the room is, and a short program switches an LED on when it gets dark. Sew it into a bag, a hat or a bedside patch for a soft glow that only appears at night — your first sensor-driven wearable.

Kati
1-2 hours

Maagizo

1

Sew the board, sensor and LED

Sew a LilyPad Arduino, a LilyPad light sensor and a LilyPad LED onto felt. Wire it: the LED's + tab to pin 5 and its - tab to -; the sensor's + tab to the board's +, its - tab to -, and its signal (S) tab to analog pin A2. Keep the power (+), ground (-) and signal lines from crossing anywhere.

Vifaa kwa hatua hii:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 kipande
LilyPad Light SensorLilyPad Light Sensor1 kipande
LilyPad LED - 5 pcsLilyPad LED - 5 pcs1 paketi
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 spu
Hand Sewing Needles (Assorted, 30-Pack)Hand Sewing Needles (Assorted, 30-Pack)1 paketi
Wool Felt SheetWool Felt Sheet1 karatasi
2

Connect the programmer

Plug the LilyPad FTDI onto the programming header and connect the USB cable to your computer. Open the Arduino IDE and select the LilyPad Arduino board and its serial port.

Vifaa kwa hatua hii:

LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V1 kipande
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 kipande

Zana zinazohitajika:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the night-light sketch

Paste this sketch and click Upload. It reads the light sensor and turns the LED on whenever the room is darker than the threshold.

lilypad_night_light.inoarduino
// LilyPad night-light: LED comes on when it gets dark.
// LED on pin 5, light sensor signal on analog pin A2.

const int LED_PIN = 5;       // LED
const int LIGHT_PIN = A2;    // light sensor signal
int threshold = 400;        // lower = waits for darker; raise to trigger sooner

void setup() {
  pinMode(LED_PIN, OUTPUT);
}

void loop() {
  int light = analogRead(LIGHT_PIN);  // 0 (dark) .. 1023 (bright)

  if (light < threshold) {
    digitalWrite(LED_PIN, HIGH);       // dark -> LED on
  } else {
    digitalWrite(LED_PIN, LOW);        // bright -> LED off
  }

  delay(100);
}
4

Calibrate the threshold

Cover the sensor with your hand — the LED should come on; in a bright room it should stay off. If it triggers too early or too late, change the threshold number in the sketch and re-upload: higher turns it on in more light, lower waits for darker.

5

Go wireless and wear it

Unplug the FTDI, sew a LilyPad coin-cell holder to the board (+ to +, - to -), drop in a CR2032 and switch on. Sew the felt onto a bag, hat or cushion — it now glows on its own whenever the light drops.

Vifaa kwa hatua hii:

LilyPad Coin Cell Battery Holder - w/Switch - 20mmLilyPad Coin Cell Battery Holder - w/Switch - 20mm1 kipande
CR2032 Coin Cell BatteryCR2032 Coin Cell Battery1 kipande

Vifaa

10

Zana Zinazohitajika

1
Jumla inayokadiriwa
$98.00

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

Blinking an LED with LilyPad Arduinona Ed
Reading a Photoresistor — SIK Circuit 6na Ed

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Making a LilyPad Musical Patchelectronics
Sewing a LilyPad LED Circuitelectronics
Sewing a LilyPad Button Circuitelectronics
Making a Color-Changing LilyPad Patchelectronics
Blinking an LED with LilyPad Arduinoelectronics
Making a Motion-Reactive LilyPad Patchelectronics

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...