Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Two-Point Marking Gauge from a Pipe Tee and Wing Bolt (Boy Mechanic, 1915)
Forge

Imeundwa na

Forge

14. Novemba 2026NO
7
0
0
0
0

Two-Point Marking Gauge from a Pipe Tee and Wing Bolt (Boy Mechanic, 1915)

A small scribing gauge built in a 3/8 in pipe tee: two flat steel bars with bent, sharpened points slide through a slot in a wood plug filling the tee, and a wing bolt screwed through a bushing in the side outlet locks them at the set distance.
Kati
Two hours

Maagizo

1

Read the Boy Mechanic

"After the points have been drawn out to the right distance, the wing bolt is turned to hold them in that position."
2

Tee and bushing

Screw a 3/8 in bushing into the side outlet of a 3/8 in pipe tee and tap the bushing to take a 7/16 in wing bolt.

Vifaa kwa hatua hii:

Kiungio cha bomba chenye nyuziKiungio cha bomba chenye nyuzi1 kipande
Bushi ya chumaBushi ya chuma1 kipande

Zana zinazohitajika:

Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
Kibano cha meza ya kaziKibano cha meza ya kazi
3

Plug and slot

Drive a tight-fitting wood plug through the run of the tee, grind its ends flush on an emery wheel, and cut a slot 5/16 in square through the plug just under the bushing.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 kipande

Zana zinazohitajika:

Gurudumu la kusagaGurudumu la kusaga
PatasiPatasi
Msumeno wa mkonoMsumeno wa mkono
4

Make the points

Cut two pieces of flat steel 1/4 in wide, 1/8 in thick and 1/8 in longer than the tee. Bend the outer end of each at right angles and sharpen it to a point. Fit both in the slot, one from each side.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kibano cha meza ya kaziKibano cha meza ya kazi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
NyundoNyundo
5

Set and lock

Draw the points out to the distance you want and turn the wing bolt down onto the bars to hold them.
6

Troubleshooting

Pipe-tee gauge troubleshooting.

Flow

Loading...
7

History and honest limits

From **The Boy Mechanic, Book 2** (Popular Mechanics, 1915), p. 294, by C. Molloy (checked on the archive.org scan boymechanicbook200chic2). The tool list is ours.

Vifaa

4

Zana Zinazohitajika

8

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...