Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)
Charlie

Imeundwa na

Charlie

7. Novemba 2026DE
6
0
0
0
0

Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)

A stand that holds flasks and basins at any height over a lamp or furnace. Michael Faraday (1830) describes the retort-stand: an upright brass rod on a heavy foot, with rings of several sizes, each on an arm whose socket slides up and down the rod and is fixed by a screw-nut at the back. Brass feet filled with lead tip over under a heavy vessel, so he makes the foot a stout board about 12 x 6 x 1 inches, the rod fixed 1 1/2 inches from one end, and stands the lamp or furnace on the board under the ring. Source: M. Faraday, Chemical Manipulation (1830), §386, p. 175. Picture: his woodcut.
Mwanzo
Unknown

Maagizo

1

Read Faraday

"It is much better to make the foot of a piece of stout board, about twelve inches in length, six inches in width, and an inch thick. The upright rod should be fixed about one inch and a half from one end of it, the lamp or furnace should be placed upon it, and the ring of course in a corresponding direction. Such an arrangement is perfectly steady, and cannot be overset by any weight which it is strong enough to bear."
2

Fix the rod in the board

Take a stout board about 12 in. long, 6 in. wide and 1 in. thick. Fix an upright brass rod in it about 1 1/2 in. from one end. Rod size, and how it is fixed, are not given (unknown). Ours: a hardwood board.

Vifaa kwa hatua hii:

Ubao wa Mti MgumuUbao wa Mti Mgumu1 futi
Ufito wa shaba ya njanoUfito wa shaba ya njano1 upright
Plagi au soketi isiyojulikanaPlagi au soketi isiyojulikana1 kipande

Zana zinazohitajika:

Vipimo visivyojulikanaVipimo visivyojulikana
3

Make the rings

Make several rings of different sizes, each fixed to an arm, and each arm to a socket that slides freely up and down the rod. Fit each socket with a screw-nut at the back to tighten it at any height. The metal and sizes are not given (unknown). Ours: wing nuts for the screw-nuts.

Vifaa kwa hatua hii:

Metali isiyojulikanaMetali isiyojulikana1 rings, arms, sockets
Nati ya mabawaNati ya mabawa1 kipande

Zana zinazohitajika:

Vipimo visivyojulikanaVipimo visivyojulikana
4

Use it

Stand the lamp or furnace on the board and turn the ring over it. Slide the ring to the height wanted and tighten the screw. Do not set a hot flask on a cold ring, or a cold, freshly filled flask on a hot ring over the fire: the bottom may come out (Faraday §388).

Vifaa

5

Zana Zinazohitajika

1

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...