Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Forge

Imeundwa na

Forge

13. Novemba 2026NO
7
0
0
0
0

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)

Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off. We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
Mwanzo
About 2 hours

Maagizo

1

Bracket blank

Inapakia daftari la Jupyter…
2

Read US 2,631,224

"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3

Bend the cell clip

Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Koleo la Mdomo BapaKoleo la Mdomo Bapa
4

Make the bulb support

Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 kipande
Waya wa chuma cha kamaniWaya wa chuma cha kamani1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Kigwe cha KatikatiKigwe cha Katikati
Koleo lenye Ncha za DuaraKoleo lenye Ncha za Duara
Koleo la Mdomo BapaKoleo la Mdomo Bapa
5

Fit the spring and handle

Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.

Vifaa kwa hatua hii:

Waya wa chuma cha kamaniWaya wa chuma cha kamani1 kipande

Zana zinazohitajika:

Koleo lenye Ncha za DuaraKoleo lenye Ncha za Duara
Koleo la Mdomo BapaKoleo la Mdomo Bapa
Koleo la kukata waya la pembeKoleo la kukata waya la pembe
6

Put in the cell and bulb

Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.

Vifaa kwa hatua hii:

Seli kavuSeli kavu1 kipande
Balbu ya tochiBalbu ya tochi1 kipande
Bamba la batiBamba la bati1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Koleo la Mdomo BapaKoleo la Mdomo Bapa
7

Fit it in the pumpkin

Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.

Vifaa kwa hatua hii:

BogaBoga1 kipande
Washa bapaWasha bapa1 kipande

Zana zinazohitajika:

Kisu cha kazi za mikonoKisu cha kazi za mikono
Koleo la Mdomo BapaKoleo la Mdomo Bapa
8

Use it

Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9

Troubleshooting

Jack-o'-lantern light troubleshooting.

Flow

Loading...
10

History and honest limits

**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.

Vifaa

6

Zana Zinazohitajika

6

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...