Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)
A flat screwdriver is a steel shank flattened to a blade that fits the slot of a screw. H. Holford's 20th Century Toolsmith and Steelworker (1907) says most smiths make them so they twist or break on a hard screw, and gives his cure: forge it from 75-point carbon steel, strike the blade a few good blows on each flat at a low heat, harden it and let the temper run to grey.
His Fig. 60 shows the shape without its handle. He gives no sizes and no handle, which are unknown here; the brine bath is from his chapter on the hardening bath.
Source: H. Holford (1907), pp. 21, 118. Picture: his Fig. 60.
Kati
Half a day
Maagizo
1
1
Read Holford
Read Holford
"Strike it a few good blows on each flat side of the screw driving edge while at a low heat. Then harden and allow the temper to draw to a grey, cool off and you will have a screw driver that will give unlimited satisfaction."
2
2
Forge the shape
Forge the shape
Take good steel of 75 points carbon. Forge it to the shape of Fig. 60: a round shank, flattened at one end to the driving blade and drawn to a pointed tang at the other for the handle. Holford gives no sizes (unknown).
Vifaa kwa hatua hii:
Kipande cha mraba cha feleji ya zana1 barZana zinazohitajika:
Jiko la Kufua
Fuawe
Nyundo ya mhunzi
Koleo za mhunzi
Vipimo visivyojulikana
Miwani ya usalama
Glavu Zinazostahimili Joto3
3
Pack the blade
Pack the blade
At a low heat, strike a few good blows on each flat side of the driving edge.
Zana zinazohitajika:
Nyundo ya mhunziFuaweJiko la KufuaKoleo za mhunzi4
4
Harden and temper grey
Harden and temper grey
Heat the blade end evenly and quench it in the hardening bath. Holford's bath is clean water free from grease, best made into a brine with as much salt as the water will dissolve, kept as large and as cold as possible. Brighten the blade with a file so the colours show, draw the temper to a grey, then cool it off.
Zana zinazohitajika:
Jiko la Kufua
Myeyusho wa chumvi uliojaaKoleo za mhunzi
Tupa lainiGlavu Zinazostahimili Joto5
5
Fit a handle
Fit a handle
Fit a handle on the tang. Holford shows the screwdriver without one and does not say what it is made of (unknown).
Vifaa kwa hatua hii:
Nyenzo isiyojulikana1 handle6
6
History and honest limits
History and honest limits
Holford, a toolsmith writing for blacksmiths and tool dressers, says a good screwdriver is prized by every mechanic, woodworkers most of all, yet few smiths could make one that would not break or twist. His temper table lists the screwdriver at grey, in 0.75 carbon steel.
He gives no sizes, no handle and no heat for hardening; those are unknown here, and the tools are ours.
Vifaa
2- Kishikilia Nafasi
- 1 handleKishikilia Nafasi
Zana Zinazohitajika
9- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.