Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock.
The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap.
Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
Juu
Unknown
Maagizo
1
1
Read Demers
Read Demers
"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2
2
Blow the vessel
Blow the vessel
Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.
Vifaa kwa hatua hii:
Kioo kisichojulikana1 vesselZana zinazohitajika:
Kichomeo cha mezani cha kupuliza kioo
Njia ya kuunda isiyojulikana
Vipimo visivyojulikana3
3
Fuse on the stopcock
Fuse on the stopcock
Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).
Vifaa kwa hatua hii:
Koki ya kioo1 plug of glass or PTFEZana zinazohitajika:
Kichomeo cha mezani cha kupuliza kiooNjia ya kuunda isiyojulikana4
4
Make the plastic stem
Make the plastic stem
Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.
Vifaa kwa hatua hii:
Nyenzo isiyojulikana1 flexible plastic stem
Pete ya O1 kipandeZana zinazohitajika:
Njia ya kuunda isiyojulikanaVipimo visivyojulikana5
5
Assemble and use
Assemble and use
Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.
Vifaa
4- 1 vesselKishikilia Nafasi
- 1 plug of glass or PTFEKishikilia Nafasi
- 1 flexible plastic stemKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Mchoro huu unatengeneza
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.