SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Metal Bucket: Tapered Sheet Steel, Wired Rim, Bail and Lid
A bucket is a watertight vessel, a cylinder or tapered cone with an open top and a flat bottom, carried by a semicircular handle called the bail. Cut the side from steel sheet to the flat pattern of a cone, roll it, rivet and solder the seam, wire the rim, set in a bottom, hang a forged bail, and make a lid to fit.
The picture: a tapered metal well bucket with its bail.
Kati
A day
Maagizo
1
1
Mark and cut
Mark and cut
Mark the side as a ring sector (step 6) with dividers, plus a lap for the seam, and a bottom disc a little larger than the base. Cut them with snips.
Vifaa kwa hatua hii:
Bati la Chuma Laini2 vipandeZana zinazohitajika:
Bikari ya ncha mbili
Mkasi wa bati2
2
Roll, rivet and solder
Roll, rivet and solder
Curve the side over the stake with a mallet until the ends lap. Drill and rivet the seam, then sweat solder into it with sal ammoniac as flux so it is watertight.
Vifaa kwa hatua hii:
Rivet za chuma8 vipande
Lehemu ya bati na risasi0.1 kg
Kloridi ya amonia (NH₄Cl)0.01 kgZana zinazohitajika:
Kigogo cha kufinyanga
Nyundo ya mbao
Kekee cha mkono
Nyundo yenye kichwa cha msalaba
Chuma cha kulehemia3
3
Wire the rim and set the bottom
Wire the rim and set the bottom
Turn the top edge over a steel wire to stiffen the rim. Turn up the edge of the bottom disc, fit it inside the base, rivet it and solder it all round.
Vifaa kwa hatua hii:
Waya wa chuma1 mRivet za chuma8 vipandeLehemu ya bati na risasi0.1 kgZana zinazohitajika:
Kigogo cha kufinyangaNyundo ya mbaoNyundo yenye kichwa cha msalabaKekee cha mkonoChuma cha kulehemia4
4
Ears and bail
Ears and bail
Forge two ears from sheet offcuts with a hole each and rivet them below the rim on opposite sides. Forge an iron rod into a semicircular bail with a hook at each end through the ears.
Vifaa kwa hatua hii:
Fito ya chuma cha kufua0.6 mRivet za chuma4 vipande
Mkaa2 as requiredZana zinazohitajika:
Fua ya mhunzi
FuaweNyundo yenye kichwa cha msalaba
Koleo za mhunzi
Glavu za kulehemu5
5
Lid
Lid
Cut a disc a little larger than the top and turn its edge down over the stake so it sits on the rim. Rivet on a strap handle.
Vifaa kwa hatua hii:
Bati la Chuma Laini1 kipandeRivet za chuma2 vipandeZana zinazohitajika:
Mkasi wa batiKigogo cha kufinyangaNyundo ya mbaoKekee cha mkono6
6
The flat pattern of a tapered bucket
The flat pattern of a tapered bucket
Inapakia daftari la Jupyter…
Vifaa
7- 2 vipandeKishikilia Nafasi
- 22 vipandeKishikilia Nafasi
- 0.2 kgKishikilia Nafasi
- 0.01 kgKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 2 as requiredKishikilia Nafasi
Zana Zinazohitajika
11- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- 2 vendors sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.