Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Spiral-Wing Spheroid Churn: A Ball Dasher on Balls Turns Freely on Its Rod, Its Spiral Wings Spinning It Each Stroke
Otis W. Stanford of Cincinnati received US 28,696, dated 12 June 1860, for a churn. On the foot of an ordinary up-and-down dash rod he hangs a round or egg-shaped wooden dasher that turns freely on balls, with spiral wings nearly touching the tub's sides. As the rod is worked, the cream spins the dasher one way then the other; the cream is squeezed between the wings and the wall, and air trapped under the round body is carried into it.
The patent gives no sizes; every size here is ours.
Kati
About 1 day, plus printing
Maagizo
1
1
How far the dasher turns each stroke
How far the dasher turns each stroke
Inapakia daftari la Jupyter…
2
2
A dash that turns as it is driven, one week before
A dash that turns as it is driven, one week before
Ross's pitched blades turn the dash and handle on a swivel. Stanford's spiral wings turn the dasher alone, on balls.
3
3
Read US 28,696
Read US 28,696
"The rod C being reciprocated, as in the common churn, the inertia of the fluid acts to swiftly rotate the dasher in successively opposite directions and this reacting upon the liquid imparts to the latter a quick succession of opposite vertical movements resulting in violent agitation."
4
4
Print the dasher's upper half
Print the dasher's upper half
Upper half of the spheroid, 150 mm across and 80 tall, with the upper halves of three spiral wings reaching 116 mm; bored 12.8 mm with a 32 mm recess for the upper ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
5
5
Print the dasher's lower half
Print the dasher's lower half
Lower half, printed upside down, with the lower halves of the wings and the recess for the lower ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Lid B with boss b
Lid B with boss b
Turn a hardwood lid to fit the bucket's rim, 20 mm thick, with a boss 60 mm across and 140 mm tall in the middle, bored 26 mm through as the guide for the rod.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu1 kipande
Gundi ya Mbao1 kipandeZana zinazohitajika:
Kerezo cha mbao
Seti ya vichwa bapa vya kutoboa
Kekee cha Betri
Sandarusi (karatasi ya kusugua)7
7
Rod C, dasher D, balls G, screw E and washer F
Rod C, dasher D, balls G, screw E and washer F
Cut a 25 mm hardwood rod 500 mm long and glue a 12 mm stainless spindle 170 mm long into its foot. Glue the two printed halves together with the wings lined up. Slide on a ring of 6 mm stainless balls in the upper recess, the dasher, and a second ring in the lower recess, and hold them with a stainless washer and a machine screw into the spindle's end. The dasher must spin freely.
Vifaa kwa hatua hii:
Vijiti vya mbao ngumu1 kipande
Fimbo ya chuma cha pua1 kipandeGundi ya Mbao1 kipande
Beringi za mipira20 vipande
Skrubu za mashine1 kipande
Uzi wa PETG1 kipandeZana zinazohitajika:
Printa ya 3D ya nyuzi (FDM)
Msumeno wa chuma
Tupa (Tupa ya Mkono)Kekee cha Betri
Seti ya vichimbuzi
Seti ya bisibisi8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket and lid cut open: the rod through the boss, the spheroid dasher with its three spiral wings on its two rings of balls, held by the washer.
9
9
Churn
Churn
Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher in and put on the lid over the rod. Work the rod up and down about 150 mm, steadily, timing it; the dasher turns one way and back. When the butter comes, lift the lid and dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Vifaa kwa hatua hii:
Malai nzito6 l
Chumvi ya Bahari Mbichi1 kipande
Maji1 kipande
Ndoo ya Lita 201 kipandeZana zinazohitajika:
Kipima joto chenye kijiti kinachobaki ndani
Saa ya kupima muda
Mizani ya dijitali ya jikoni
Bakuli kubwa la kuchanganyia la chuma cha pua10
10
Troubleshooting
Troubleshooting
Spiral-wing dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Otis W. Stanford** of Cincinnati, Hamilton County, Ohio, US 28,696, 12 June 1860, "Churn". He claimed the upright tub with the reciprocating rod, the spheroidal dasher and spiral wings fitting the tub. His dasher is wooden; ours is printed in two halves, and the wings' number, twist and every size are ours.
Vifaa
11- 1 kipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 20 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 6 lKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
13- Kishikilia Nafasi
- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Faili za muundo
3Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
Balance-Wheel Churn Frame: A Weighted Wheel Drives the Dash Up and Down and Its Pitched Blades Make It Revolve
na Buttercup
Utengenezaji mbao
0
0
0
0
0
0
Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
na Buttercup
Utengenezaji mbao
0
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
na TheChef
UJANJA
60
0
0
0
0
0
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.