SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Frank A. Stanley · Public domain (1919)
Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)
Die makers made their own dowel pins two at a time: one piece of steel is turned, necked in the middle, hardened, ground dead straight to size from each end, then snapped in two at the neck. Frank Stanley described the practice of one die shop.
Source: F. A. Stanley, Punches and Dies (1919), pp. 417–419. The choice of tool steel and the forge for hardening are ours; the passage gives no hardening heat. Picture: Stanley's Fig. 610, grinding dowel pins.
Kati
1 day
Maagizo
1
1
Cut stock for two pins
Cut stock for two pins
Take a length of steel a little larger than the dowel size and long enough for two pins. It must harden, so use tool steel (our choice).
Vifaa kwa hatua hii:
Kipande cha pembe nane cha feleji ya zana1 length for two pinsZana zinazohitajika:
Kibano cha meza ya kazi2
2
Turn 0.008 in over size
Turn 0.008 in over size
Turn it on centres to about 0.008 in above the finished size.
Zana zinazohitajika:
Kereza ya Chuma
Kivuta cha kereza
Maikromita3
3
Neck it in the middle
Neck it in the middle
Cut a neck 1/16 in deep in the middle, the dividing line between the two pins.
Zana zinazohitajika:
Kereza ya Chuma4
4
Harden
Harden
Harden the piece. This passage gives no heat; heat to hardening heat and quench in the usual way for your steel (ours).
Zana zinazohitajika:
Fua ya mhunzi
Koleo
Ndoo ya kupoza chuma5
5
Grind each half to size
Grind each half to size
Put it on dead centres in the grinding machine and grind the diameter to size from one end to the neck. Reverse it on the centres and grind from the other end. The pins come out perfectly straight from end to end.
Zana zinazohitajika:
Mashine ya kusaga mviringoKivuta cha kerezaMaikromita6
6
Break the pins apart
Break the pins apart
Break the piece apart at the neck. You have two dowel pins ground closely to standard size; ream their holes true and straight to fit.
Zana zinazohitajika:
Kibano cha meza ya kaziVifaa
1- 1 length for two pinsKishikilia Nafasi
Zana Zinazohitajika
8- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.