Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
6
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
Juu
Several weeks

Maagizo

1

His layout data

Inapakia daftari la Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe4 vipande
Ubao wa mwereziUbao wa mwerezi6 vipande
Ubao wa msonobariUbao wa msonobari3 vipande

Zana zinazohitajika:

Msumeno wa kupasuaMsumeno wa kupasua
Msumeno wa mkonoMsumeno wa mkono
Randa ya mkonoRanda ya mkono
Tepi ya kupimiaTepi ya kupimia
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Vifaa kwa hatua hii:

Ubao wa msonobariUbao wa msonobari2 vipande
Karatasi nzitoKaratasi nzito1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
RulaRula
PenseliPenseli
MkasiMkasi
NyundoNyundo
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe2 vipande
Skrubu za mbao za shaba ya njanoSkrubu za mbao za shaba ya njano4 vipande

Zana zinazohitajika:

Kisu cha KuvutaKisu cha Kuvuta
Randa ya mkonoRanda ya mkono
Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Bisibisi bapaBisibisi bapa
Klampu ya umbo la CKlampu ya umbo la C
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe2 vipande
Ubao wa msonobariUbao wa msonobari1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

Kipima pembe cha nyuzi tisiniKipima pembe cha nyuzi tisini
NyundoNyundo
PatasiPatasi
Randa ya mkonoRanda ya mkono
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Vifaa kwa hatua hii:

Ubao wa mwereziUbao wa mwerezi2 vipande
Misumari ya shaba yenye kichwa kipanaMisumari ya shaba yenye kichwa kipana1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
NyundoNyundo
Tepi ya kupimiaTepi ya kupimia
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Vifaa kwa hatua hii:

Ubao wa mwereziUbao wa mwerezi4 vipande
Misumari ya shaba yenye kichwa kipanaMisumari ya shaba yenye kichwa kipana1 kipande
Vipini vidogo vya shabaVipini vidogo vya shaba1 kipande

Zana zinazohitajika:

Uma wa kutoboa (ushindilio)Uma wa kutoboa (ushindilio)
Klampu ya umbo la CKlampu ya umbo la C
Chuma cha kukunja misumariChuma cha kukunja misumari
NyundoNyundo
Msumeno wa mkonoMsumeno wa mkono
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe2 vipande
Ubao wa mwereziUbao wa mwerezi1 kipande
Misumari ya shaba yenye kichwa kipanaMisumari ya shaba yenye kichwa kipana1 kipande
Skrubu za mbao za shaba ya njanoSkrubu za mbao za shaba ya njano30 vipande
Kitambaa cha kanvasiKitambaa cha kanvasi1 kipande

Zana zinazohitajika:

Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
Bisibisi bapaBisibisi bapa
Msumeno wa mkonoMsumeno wa mkono
PatasiPatasi
NyundoNyundo
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Vifaa kwa hatua hii:

Kitambaa cha kanvasiKitambaa cha kanvasi1 kipande
Gundi ya bahariniGundi ya baharini1 kipande
Vipini vidogo vya shabaVipini vidogo vya shaba1 kipande

Zana zinazohitajika:

Kopo la batiKopo la bati
Brashi pana ya rangiBrashi pana ya rangi
Pasi ya chumaPasi ya chuma
MkasiMkasi
NyundoNyundo
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Vifaa kwa hatua hii:

Ukanda wa mbao nusu duaraUkanda wa mbao nusu duara1 kipande
Ukanda wa shaba wa omo la mashuaUkanda wa shaba wa omo la mashua2 vipande
Skrubu za mbao za shaba ya njanoSkrubu za mbao za shaba ya njano12 vipande
Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande
MisumariMisumari1 kipande

Zana zinazohitajika:

NyundoNyundo
Bisibisi bapaBisibisi bapa
Randa ya mkonoRanda ya mkono
Kekee cha mkonoKekee cha mkono
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Vifaa kwa hatua hii:

Vanishi ya shelakiVanishi ya shelaki1 kipande
Rangi ya mafutaRangi ya mafuta1 kipande
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)1 kipande
Varnishi ya milingotiVarnishi ya milingoti1 kipande
Ubao wa msonobariUbao wa msonobari1 kipande

Zana zinazohitajika:

Brashi pana ya rangiBrashi pana ya rangi
Bisibisi bapaBisibisi bapa
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Vifaa

16

Zana Zinazohitajika

21

Mchoro huu unatengeneza

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...