Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
Kati
About 1 week
Maagizo
1
1
Fig. 5 in centimetres, and the wax
Fig. 5 in centimetres, and the wax
Inapakia daftari la Jupyter…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3
3
Get and choose the wood
Get and choose the wood
Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu2 vipandeZana zinazohitajika:
Msumeno wa mkono
Tepi ya kupimia4
4
Lay out and saw
Lay out and saw
Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu1 kipandeZana zinazohitajika:
Penseli
Msumeno wa mkono
Tepi ya kupimia5
5
Plane to thickness
Plane to thickness
Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.
Zana zinazohitajika:
Randa ya mkono
Randa ya mikono miwili6
6
Steam the tip
Steam the tip
Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.
Zana zinazohitajika:
Sufuria Kubwa
Mopu
Kibano cha upau7
7
Binding hole, balance and groove
Binding hole, balance and groove
Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.
Vifaa kwa hatua hii:
Ukanda wa Ngozi2 vipandeZana zinazohitajika:
Kekee cha mkono
Patasi
Patasi ya Bapa-Pinda
Msumeno wa mkono8
8
Finish and wax
Finish and wax
Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.
Vifaa kwa hatua hii:
Sandarusi (karatasi ya kusugua)1 kipande
Mafuta ya Kitani1 kipande
Nta ya parafini1 kipande
Nta ya Nyuki1 kipande
Ubani wa msonobari1 kipande
Tapentaini1 kipandeZana zinazohitajika:
Sufuria Kubwa
Pasi ya chuma
Brashi pana ya rangi9
9
Troubleshooting
Troubleshooting
Ski troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.
Vifaa
8- 2 vipandeKishikilia Nafasi
- 2 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
13- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.


