Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Trowel: the Moulder's Trowel Forged from Flat Steel (Modern Shop Practice, 1916)
A trowel with a wide thin steel blade and a short stem cranked up at a right angle to a round handle. Modern Shop Practice (1916) forges it from steel about 1/4 inch by 1 inch: nick it with fullers, draw down the stem, bend it up to a square corner, then thin the blade edge by edge so a small ridge stays where the stem joins (Fig. 121, R).
The foundry uses it to shape and smooth the larger surfaces of a mould; the bottom is ground slightly crowning so the forward edge does not cut into the sand. Blade size, steel grade and the handle are not given.
Source: Modern Shop Practice, vol. 4 (American Technical Society, 1916), Forging p. 65 and Foundry Work pp. 14-15. Picture: Figs. 121-122.
Kati
An hour
Maagizo
1
1
Read the source
Read the source
"The molder's trowel illustrated in Fig. 121 is a sample of a large class of forgings, having a wide thin face with a comparatively small thin stem forged at one end. The stock used for the trowel would be about 1/4 inch by 1 inch. This is thick enough to allow for the formation of a ridge at R."
2
2
Nick and draw the stem
Nick and draw the stem
Heat the 1/4 × 1 inch steel. Make two nicks across it with fullers near one end (Fig. 122, A) and draw that end down, roughly to size, into the stem.
Vifaa kwa hatua hii:
Fimbo ya chuma ghafi1 barZana zinazohitajika:
Jiko la Kufua
Fuawe
Nyundo ya mhunzi
Koleo za mhunzi
Fuller (chombo cha kuchora mifereji)
Glavu Zinazostahimili Joto3
3
Bend the square corner
Bend the square corner
Bend the stem up at a right angle and forge it to a square corner (Fig. 122, B), the same way as the square corner of a bracket.
Zana zinazohitajika:
Jiko la KufuaFuaweNyundo ya mhunziKoleo za mhunziGlavu Zinazostahimili Joto4
4
Flatten the blade
Flatten the blade
Hold the work with the stem pointing down against the side of the anvil (Fig. 122, C). Strike down so the blows cover the part over the edge of the anvil: all the metal on the anvil is flattened. Swing the piece round to thin the other edge. The small triangle left unworked forms the ridge R. The same result comes from laying the work flat on the anvil face and using a set hammer. Blade width and length are not given (unknown).
Zana zinazohitajika:
Jiko la KufuaFuaweNyundo ya mhunziKoleo za mhunzi
Nyundo ya kuweka bega
Vipimo visivyojulikanaGlavu Zinazostahimili Joto5
5
Grind the bottom and fit the handle
Grind the bottom and fit the handle
Grind the bottom of the blade slightly crowning, so it can be rocked a little as it is worked over the sand without the forward edge cutting in. Fit a short round handle that fits the grasp of the hand (Fig. 10); the source does not say what it is made of or how it is fixed to the stem.
Vifaa kwa hatua hii:
Mpini wa Kifaa1 kipandeZana zinazohitajika:
Gurudumu la kusaga6
6
History and honest limits
History and honest limits
The book counts sixty or more trowel and slick shapes on the market; the square trowel works into square corners, the finishing trowels cope out along curved pattern edges. Trowels are sold by width and length of blade.
Not given: blade size, steel grade, handle material and fixing, any hardening. Steel Bar Stock stands for the plain "steel" of the source.
Vifaa
2- 1 barKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
9- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.