SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Two-Tine Pitchfork Split from One Iron Bar
Youblob · CC0
Forge

Imeundwa na

Forge

14. Oktoba 2026NO
12
0
0
0
0

Two-Tine Pitchfork Split from One Iron Bar

A pitchfork pitches hay, straw, manure or leaves: a long wooden shaft and slightly curved metal tines, wide apart for hay. Split one end of a wrought-iron bar, draw the halves into two round tines, draw a tang at the other end and fit it into the shaft under an iron ferrule. The picture: our diagram of the four stages.
Kati
A day

Maagizo

1

Draw the tang

Heat one end of the bar and draw a square tapered tang about 10 cm long.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo yenye kichwa cha msalabaNyundo yenye kichwa cha msalaba
Koleo za mhunziKoleo za mhunzi
Glavu za kulehemuGlavu za kulehemu
2

Split the bar

At a good heat, split the other end down the middle over the hot cut, about 12 cm deep, working from both faces.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
Patasi ya kukata kwenye fuawePatasi ya kukata kwenye fuawe
Nyundo yenye kichwa cha msalabaNyundo yenye kichwa cha msalaba
Koleo za mhunziKoleo za mhunzi
Glavu za kulehemuGlavu za kulehemu
3

Draw the tines

Open the two halves into a V, then draw each one out round and to a point. Bend them parallel, about 15 cm apart, and give them a slight curve.

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo yenye kichwa cha msalabaNyundo yenye kichwa cha msalaba
Koleo za mhunziKoleo za mhunzi
Glavu za kulehemuGlavu za kulehemu
4

Ferrule

Cut a strip of sheet iron, roll it hot into a ring that fits tightly over the end of the shaft, and drive it on.

Vifaa kwa hatua hii:

Bamba la chuma (lililofuliwa)Bamba la chuma (lililofuliwa)1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Fua ya mhunziFua ya mhunzi
FuaweFuawe
Nyundo yenye kichwa cha msalabaNyundo yenye kichwa cha msalaba
Koleo za mhunziKoleo za mhunzi
Glavu za kulehemuGlavu za kulehemu
5

Fit the shaft

Drill the shaft end for the tang, drive the tang in, and pin it through the ferrule with a nail. File the tine points clean.

Vifaa kwa hatua hii:

Fimbo ya mbao iliyonyookaFimbo ya mbao iliyonyooka1 kipande
Misumari ya ChumaMisumari ya Chuma1 kipande

Zana zinazohitajika:

Kekee cha mkonoKekee cha mkono
Nyundo yenye kichwa cha msalabaNyundo yenye kichwa cha msalaba
Tupa ya chumaTupa ya chuma
6

Tine length

Inapakia daftari la Jupyter…

Vifaa

4

Zana Zinazohitajika

9

Mchoro huu unatengeneza

Thumbnail
Kishikilia nafasi

Uma wa nyasi

Free

14
0

Blueprint zinazohusiana

Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni

Iron Fire Rake Forged from One Bar

Iron Fire Rake Forged from One Bar

na ForgeNO

Mhunzi

14
0
0
0
0
0

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...