Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Paul N. Hasluck (ed.) · Public domain (published 1907)
Forge

Imeundwa na

Forge

4. Novemba 2026NO
6
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
Kati
Unknown

Maagizo

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 body, bottom
Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 edge
Lehemu ya bati na risasiLehemu ya bati na risasi1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
KigingiKigingi
Nyundo ya mbaoNyundo ya mbao
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
FluksiFluksi
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 spout, stay
Lehemu ya bati na risasiLehemu ya bati na risasi1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
KigingiKigingi
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
FluksiFluksi
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 rose
Lehemu ya bati na risasiLehemu ya bati na risasi1 kipande

Zana zinazohitajika:

Bikari ya ncha mbiliBikari ya ncha mbili
Mkasi wa batiMkasi wa bati
KigingiKigingi
Nyundo ya kulainishaNyundo ya kulainisha
Uma wa kutoboa (ushindilio)Uma wa kutoboa (ushindilio)
Kipande cha mbao ngumuKipande cha mbao ngumu
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
FluksiFluksi
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

Vifaa kwa hatua hii:

Bamba la batiBamba la bati1 top, handles, studs
Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 No. 12 B.W.G.
Lehemu ya bati na risasiLehemu ya bati na risasi1 kipande

Zana zinazohitajika:

Mkasi wa batiMkasi wa bati
Nyundo ya kulainishaNyundo ya kulainisha
Patasi ya chumaPatasi ya chuma
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
FluksiFluksi
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

Vifaa kwa hatua hii:

Rangi ya mafutaRangi ya mafuta2 coats

Zana zinazohitajika:

TapentainiTapentaini
Kaboneti ya kalsiamu (chaki nyeupe)Kaboneti ya kalsiamu (chaki nyeupe)

Vifaa

4

Zana Zinazohitajika

12

Vifaa vya Michoro Iliyounganishwa

Tinplate and Galvanized Steel Sheet from Coil
Usambazaji 10%

Tinplate and Galvanized Steel Sheet from Coil

na EmmaSE

Uchimbaji chuma

25
0
0
0
5
0
Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)
Usambazaji 10%

Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)

na ForgeNO

Industry 2.0 — Electricity, Steel & Oil (1870)

7
0
0
0
2
0

Mchoro huu unatengeneza

Thumbnail
Kishikilia nafasi

Chombo cha kumwagilia maji

Free

64
0
1

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...