Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
Forge

Imeundwa na

Forge

15. Novemba 2026NO
5
0
0
0
0

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)

C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
Kati
A day

Maagizo

1

The steps

Inapakia daftari la Jupyter…
2

Read Willey

"A very efficient, quick-opening and closing vise for the drill-press table."
3

Make the bed

Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kigwe cha KatikatiKigwe cha Katikati
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
4

Make the end supports

Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande
Mkusanyiko wa bolti za pembe sitaMkusanyiko wa bolti za pembe sita1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
5

Make the fixed jaw

Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande
Ufito wa chuma lainiUfito wa chuma laini1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Nyundo yenye kichwa cha duaraNyundo yenye kichwa cha duara
6

Make the sliding jaw

Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande
Ufito wa chuma lainiUfito wa chuma laini1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Tupa (Tupa ya Mkono)Tupa (Tupa ya Mkono)
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Nyundo yenye kichwa cha duaraNyundo yenye kichwa cha duara
Kibano cha meza ya kaziKibano cha meza ya kazi
7

Make the cam

Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.

Vifaa kwa hatua hii:

Shafti ya chumaShafti ya chuma1 kipande
Ufito wa chuma lainiUfito wa chuma laini1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Nyundo yenye kichwa cha duaraNyundo yenye kichwa cha duara
8

Use it

Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.

Vifaa kwa hatua hii:

Mkusanyiko wa bolti za pembe sitaMkusanyiko wa bolti za pembe sita1 kipande

Zana zinazohitajika:

Kekee cha NguzoKekee cha Nguzo
9

Troubleshooting

Drill vise troubleshooting.

Flow

Loading...
10

History and honest limits

From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.

Vifaa

4

Zana Zinazohitajika

7

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...