Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Easter Egg Dyeing Stand: a Crank-Turned Rubber Roller Spins the Egg Under the Brush (Young, 1943)
Woody

Imeundwa na

Woody

13. Novemba 2026NO
7
0
0
0
0

Easter Egg Dyeing Stand: a Crank-Turned Rubber Roller Spins the Egg Under the Brush (Young, 1943)

Raymond P. Young of Wrightsville, Pennsylvania, received US 2,327,754, dated 24 August 1943, for a little table for dyeing Easter eggs. The egg sits in an oval opening on a rubber roller turned by a crank; hold a dye brush against it and the colour goes on evenly all round. Grooves hold the brushes, a rack holds the dye bottles, and a rabbit stands at one end. We make it from plywood and dowel. All sizes are ours.
Mwanzo
About 4 hours

Maagizo

1

Opening and roll

Inapakia daftari la Jupyter…
2

Read US 2,327,754

"If a dye containing brush is held against the object 8, application of the dye to the object 8 will take place uniformly and in a convenient manner."
3

Cut the platform

Cut a platform of 12 mm plywood about 300 x 180 mm (ours). Near one corner cut an oval opening 70 x 40 mm with a coping saw, his opening 6. Glue a strip of thin plywood or a ring of dowel round it to make the rise 7, so the egg cannot roll off.

Vifaa kwa hatua hii:

Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

PenseliPenseli
Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkonoKekee cha mkono
Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)
4

Make the brush grooves

Glue short dowels across the top of the platform beside the opening, a little apart, so the gaps between them (his ribs 10 and grooves 11) hold the brushes.

Vifaa kwa hatua hii:

Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)
5

Fit the legs

Drill the corners and glue in four dowel legs, his legs 9, long enough to clear the crank below (ours).

Vifaa kwa hatua hii:

Vijiti vya mbao ngumuVijiti vya mbao ngumu1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Kekee cha mkonoKekee cha mkono
Msumeno wa mkonoMsumeno wa mkono
6

Make the roller

Slide rubber tubing over a steel rod for the roll 24 (his roll is rubber, "or any other suitable material"). Bend the rod's long end twice at right angles in the vice to make the crank handle 25.

Vifaa kwa hatua hii:

Bomba la MpiraBomba la Mpira1 kipande
Ufito wa chuma lainiUfito wa chuma laini1 kipande

Zana zinazohitajika:

Kibano cha meza ya kaziKibano cha meza ya kazi
Msumeno wa chumaMsumeno wa chuma
7

Hang the roller

Cut two bearing brackets from flat bar (ours, his bearings 21 and 22), drill each for the rod at the depth the notebook gives, bend them to hang below the platform and screw them on either side of the opening, so the roll sits under the opening as his Fig. 4. The egg should rest on the roll inside the rise and turn when the crank turns.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Kibano cha meza ya kaziKibano cha meza ya kazi
Seti ya bisibisiSeti ya bisibisi
8

Make the bottle rack

Bend a strip of flat bar (his rack bar 14, "preferably strap iron") down and out at each end, drill a row of holes in it to hold the dye bottles, and screw its ends to the back edge of the platform.

Vifaa kwa hatua hii:

Pau Bapa la Chuma LainiPau Bapa la Chuma Laini1 kipande
Parafujo za mbaoParafujo za mbao1 kipande

Zana zinazohitajika:

Msumeno wa chumaMsumeno wa chuma
Kekee cha NguzoKekee cha Nguzo
Seti ya vichimbuziSeti ya vichimbuzi
Kibano cha meza ya kaziKibano cha meza ya kazi
Seti ya bisibisiSeti ya bisibisi
9

Add the rabbit

Cut a rabbit from plywood with the coping saw, sand it and glue it upright at the far end, his figure 13.

Vifaa kwa hatua hii:

Bati la mbao za kubandikaBati la mbao za kubandika1 kipande
Gundi ya MbaoGundi ya Mbao1 kipande

Zana zinazohitajika:

Msumeno wa kukata mikunjoMsumeno wa kukata mikunjo
Sandarusi (karatasi ya kusugua)Sandarusi (karatasi ya kusugua)
10

Dye an egg

Fill the bottles with food colouring (ours) and put them in the rack. Set a hard-boiled egg in the opening on the roll, turn the crank, and hold a dye-filled brush against the egg: the colour goes on in an even band. Move the brush across to stripe it.

Vifaa kwa hatua hii:

YaiYai1 kipande
Rangi ya chakulaRangi ya chakula1 kipande
Chupa za kioo zenye vifunikoChupa za kioo zenye vifuniko1 kipande

Zana zinazohitajika:

Seti ya brashi za rangiSeti ya brashi za rangi
11

Troubleshooting

Egg dyeing stand troubleshooting.

Flow

Loading...
12

History and honest limits

**Raymond P. Young** of Wrightsville, Pennsylvania, US 2,327,754, dated 24 August 1943, filed 27 May 1942. He claimed "dyeing apparatus comprising a platform having an opening therein, a rotatable roller mounted at the underside of the platform and partly protruding into said opening, means for rotating the roller, and an upstanding article confining wall on the platform surrounding said opening". He gives no sizes or dye: the plywood, dowels, all sizes, the bracket bearings, the rubber tube on a rod, and food colouring are ours.

Vifaa

10

Zana Zinazohitajika

11

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...