예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Fit: A Joint That Needs a Mallet Is Too Tight
A joint you have to drive home with a mallet will not be stronger for it. It will be weaker, because the fibres are crushed, there is nowhere for the glue to sit, and the glue that was there has been scraped off on the way in.
The target is a joint that goes together with firm hand pressure, or at most a few light taps, and stays together on its own when you let go. That leaves a glue line a few hundredths of a millimetre thick, which is what modern wood glues are formulated for.
A slack joint is also a bad joint, and for the opposite reason: PVA has essentially no gap-filling ability, so a visible gap is a joint held by a brittle film of dried glue. The useful range between the two is narrow, and it is worth knowing in numbers.
중급
3 hours
안내
1
1
How tight is right, in numbers
How tight is right, in numbers
Jupyter 노트북 불러오는 중…
이 단계의 재료:
경목 판재1 개
PVA 목공용 접착제1 개필요한 도구:
틈새 게이지 세트
디지털 캘리퍼스 6인치
데스크톱 컴퓨터2
2
Pare to fit, and pare the right piece
Pare to fit, and pare the right piece
Push the joint together until it binds, then look for the shiny spots — where it has rubbed is where it is tight. Pare those and only those. Taking a shaving off the whole cheek turns a tight joint straight into a slack one.
A sharp chisel takes a controlled shaving; a dull one skips and digs. Fitting is the operation that most rewards a freshly honed edge, and most punishes a tired one.
Pare the part that is hidden. On a mortise and tenon, pare the tenon rather than the mortise walls, because the tenon disappears. On a dovetail, pare the pins.
이 단계의 재료:
경목 판재1 개필요한 도구:
끌
바이스(만력)디지털 캘리퍼스 6인치3
3
Fit dry, and only once
Fit dry, and only once
Assemble the whole thing dry, check it for square and for wind, and take it apart again. That is the dry-run rung, and this is the rung where it pays: a joint discovered to be tight with glue in it is a genuine emergency.
Assemble dry as FEW times as possible. Wood compresses a little each time, so a joint tested five times is looser than the one tested once. If a joint is right, leave it alone.
Number the joints as you take them apart. Hand-fitted joints are fitted to each other and are not interchangeable, and a pencil mark on the inside face saves finding that out during the glue-up.
이 단계의 재료:
경목 판재1 개필요한 도구:
조합 직각자
뒤틀림 확인용 막대 한 쌍
바 클램프4
4
The clamps are for holding it, not for closing it
The clamps are for holding it, not for closing it
If the joint needs clamp pressure to close, it does not fit. Clamps are there to hold surfaces in contact while the glue cures, and to squeeze the line thin — not to drag parts into position.
A frame pulled square by clamps springs back out of square the moment they come off, because nothing has changed about the geometry of the parts. The shoulders are what make it square, and clamps cannot fix a shoulder.
Which makes the whole batch one argument. The wood will move whatever you do; the joint holds because its long grain is glued and its shape interlocks; and the fit is what decides whether the glue line is a bond or a filler. None of those can be corrected with pressure at the end.
이 단계의 재료:
PVA 목공용 접착제1 개필요한 도구:
바 클램프조합 직각자관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.