협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Glass Fibre Mat: Blown Glass Wool Drafted into a Bonded Sheet (Slayter 1942)
Blown glass wool lands on a moving screen as a loose, weak tangle. Slayter pulled a thin web off its front edge two to four times faster than the screen moves, so the fibres line up lengthwise but still cross each other, and then soaked and dried it in a binder. The result is a thin, even, strong glass sheet, used for insulation, filters and separators between battery plates.
Source: Games Slayter (Owens-Corning Fiberglas), US 2,306,347 (1942). Unknown: the glass and the binder. Slayter names neither the glass nor the binder's strength, so both are linked to unknown heads. Speeds and temperatures are not given either. Picture: the patent's Fig. 1.
고급
continuous
안내
1
1
Blow fibres from the bushing
Blow fibres from the bushing
Let molten glass run in many streams from one or more electrically heated bushings. Gas blasts from jets around the streams draw them out into long, fine fibres, which set at once as they fall through a forming hood. Unknown: the glass, the bushing temperature and the blast. Slayter gives none of them.
이 단계의 재료:
미상의 유리1 as required필요한 도구:
유리섬유 부싱
강압 변압기
성형 후드
내열 장갑
보안경2
2
Collect a mat on a moving screen
Collect a mat on a moving screen
The fibres land on an endless wire screen running over rollers, with a suction box under it to draw off the blast and hold the fibres down. They pile up in every direction as a mat. If you like, spray a lubricant into the hood first (oil, soap, fatty acid, glycerin or graphite are named), so the fibres slide past each other when drafted.
필요한 도구:
망 컨베이어
송풍기성형 후드3
3
Draft a web off the front edge
Draft a web off the front edge
Pull a thin web from the front edge of the mat over an idler roller set slightly above the screen, faster than the screen moves. Slayter recommends a 3 to 1 draft for long fibres and 2 to 1 up to 4 to 1 in general. The fibres turn mostly lengthwise but stay crossed, which holds the sheet together across its width.
필요한 도구:
연신 롤망 컨베이어4
4
Soak it in binder between the drafting rolls
Soak it in binder between the drafting rolls
Lead the web down under the surface of a pool of binder solution and between the drafting pinch rolls. The lower roll is perforated and half under the liquid. The rolls set the draft through a variable-speed drive and squeeze out the excess binder, which runs back into the tank. Unknown: the binder. For battery separators Slayter wants one that keeps the sheet porous: 'a relatively weak solution' of phenolic resin, rubber, starch, gelatin, polystyrene or methyl methacrylate, with no strength given.
이 단계의 재료:
미상의 결합제1 as required필요한 도구:
연신 롤5
5
Dry it under slight tension
Dry it under slight tension
Pull the wet sheet through a drying oven with a second pair of pinch rolls, blowing heated air through against the sheet's direction. Keep only a slight draft, 1.05 to 1 up to 1.5 to 1, so the sheet neither wrinkles across nor stretches lengthwise as the binder sets. Unknown: the oven temperature. Wind the dry mat onto a roll.
필요한 도구:
건조 가마연신 롤송풍기이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.