예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Half-Round Can Opener: Push the Cutter In and Twist
Opening a sardine box or tin with a flat knife takes many strokes and leaves a ragged edge.
Seth P. Chapin of Atlantic, New Jersey, received US 56,368, dated 17 July 1866, for an implement for opening sheet-metal cans and boxes: a cutter semicircular in section with sloping edges to a point, bevelled inside, on a handle; forced in nearly to the handle and twisted, it cuts a circle the size of its own curve, and a guard at its top keeps it in position and stops it going too deep.
This rung works out how many twists a hole takes, then files the cutter from steel tube and opens a can.
초급
About 2 hours
안내
1
1
Twists for a full circle
Twists for a full circle
Jupyter 노트북 불러오는 중…
2
2
A cutter turned round before it
A cutter turned round before it
The embedded blueprint shears tin round a wheel. Chapin bends the blade into a half-tube so twisting it cuts a circle.
3
3
Read US 56,368
Read US 56,368
"The said edges a are beveled upon their inner side to make them sufficiently sharp, and the implement is used for cutting circular holes in the tin box by forcing it, point first, into and through the sheet metal nearly up to the end of the handle A, and then turning or twisting the cutter around by means of the said handle, which causes the foremost of the edges a to cut the thin metal in a circular line corresponding to the circle of which the back or convex side of the cutter forms an arc."
4
4
Cut the half tube
Cut the half tube
Cut 45 mm of 25 mm steel tube and saw it in half lengthwise. Keep one half.
이 단계의 재료:
구조용 강관1 개필요한 도구:
쇠톱(핵소)
바이스(만력)
유성 매직
자5
5
Shape the point
Shape the point
File both long edges to slope in to a point at one end, over the last 25 mm. Bevel them inside with a round needle file and hone.
필요한 도구:
줄 (손줄)
정밀 줄(니들 파일) 세트
숫돌바이스(만력)
투명 보안경6
6
Guard and handle
Guard and handle
Epoxy a large flat washer across the cutter's top as the guard, and a hardwood handle above it.
이 단계의 재료:
평와셔1 개
단단한 나무 목심1 개
2액형 에폭시1 개필요한 도구:
사포7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: a 25 mm half-tube cutter with sloping edges to a point, the washer guard and the hardwood handle.
8
8
Twist out a hole
Twist out a hole
Stand a sealed can on the kitchen scale. Force the point through the top until the guard meets it, then twist round; count the twists, read the peak load and measure the hole.
이 단계의 재료:
양철통1 개필요한 도구:
디지털 주방 저울
디지털 캘리퍼스 6인치
스톱워치
가죽 작업 장갑9
9
A cutter that will not enter, wanders or jams
A cutter that will not enter, wanders or jams
Half-round can opener troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Seth P. Chapin** of Atlantic, Monmouth County, New Jersey, received US 56,368, dated 17 July 1866, for opening tin or other sheet-metal boxes in circles or straight or irregular lines. Widened at its widest part, the cutter cuts a larger part of a circle or oval at one thrust, leaving a piece easily bent over; another form has one edge flattened for sardine boxes, and a metal handle with a cross-piece for turning. Wyman's 1868 patent names it.
**Honest limits.** A washer stands in for his guard, and the tube is unhardened. Your twist counts are the result.
필요 도구
13- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.