협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Hydraulic Test Pump: Brass Valve Box with Glass Marble Valves and a Gas-Barrel Plunger (Cassell's, 1903)
A hand pump for testing a small boiler, a pipe or a fitting with water under pressure. Cassell's Cyclopaedia of Mechanics (1903) drills a brass rod into a valve box, uses two glass playing marbles as the valves, and works a plunger in a short length of gas or steam pipe through a gland made from an ordinary socket and nipple.
The source says it "would stand a pressure of 250 lb. per square inch easily". It has no gauge of its own: read the pressure on the work being tested.
Source: P. N. Hasluck (ed.), Cassell's Cyclopaedia of Mechanics, Third Series (1903), p. 291, "Simple Hydraulic Testing Pump". Picture: its Figs. 1-3.
중급
Unknown
안내
1
1
Read Cassell's
Read Cassell's
"The pump here illustrated is designed for use in testing a small boiler, and for similar purposes; it will fulfil the purpose of pumps of costly design and workmanship, and can be built for a few pence. It consists of a rod of solid brass or gun-metal drilled out to the required sizes as shown in Fig. 1, and fitted with ordinary iron gas or steam bends at the top and bottom of valve box."
2
2
Drill the valve box
Drill the valve box
Drill a rod of solid brass (or gun-metal) lengthwise from both ends to the sizes in Fig. 1, so that each glass marble drops into a seating made by the drill: the suction valve below, the discharge valve above. Drill and tap both ends for the iron gas or steam pipe bends, and drill and tap the centre of the side to take the pump barrel. No sizes are given (unknown).
이 단계의 재료:
황동 봉1 valve box필요한 도구:
바이스(만력)
탁상 드릴
드릴 비트 세트
나사내기 탭·다이스 세트
알 수 없는 치수3
3
Fit the valves and bends
Fit the valves and bends
Drop a glass marble into each seating (glass is preferred: it is far rounder than clay marbles). Screw an iron gas or steam pipe bend into the bottom (the suction) and another into the top (the delivery). The upper pipe carries a small cross-bar that stops the discharge marble from blocking the outlet (Fig. 3); its material is not given (unknown).
이 단계의 재료:
유리구슬2 개
나사식 배관 이음쇠2 pipe bends
알 수 없는 재료1 cross-bar필요한 도구:
파이프 렌치4
4
Make the barrel and gland
Make the barrel and gland
Cut a short length of gas or steam pipe for the barrel: its length is set by the stroke the pump is to have. Screw one end into the valve box. Countersink the other (gland) end, screw an ordinary socket over it, and screw into the socket an ordinary nipple, also countersunk, as the gland. Fit a back nut on the nipple for screwing up the gland and fix it with a rivet so it cannot turn.
이 단계의 재료:
수도관1 short length나사식 배관 이음쇠2 socket and nipple
고정 너트1 개
철 리벳1 개필요한 도구:
쇠톱(핵소)
카운터싱크 드릴 비트 세트파이프 렌치
볼핀 해머5
5
Make the plunger
Make the plunger
File out the inside of the barrel roughly to remove scale and unevenness left by the pipe mandrel. Turn a plunger to fit it loosely, file two flats on one end and drill a hole there for a pin. The plunger's material and what the pin holds are not given (unknown).
이 단계의 재료:
알 수 없는 재료1 plunger필요한 도구:
줄 (손줄)
금속 선반탁상 드릴드릴 비트 세트6
6
Mount and use
Mount and use
Fix the pump down with two ordinary bent clips over the barrel near its ends (Fig. 2). Put the suction bend in water, connect the delivery to the work and work the plunger. Cassell's: the pump "would stand a pressure of 250 lb. per square inch easily". The clip material is not given (unknown).
이 단계의 재료:
알 수 없는 재료2 bent clips필요한 도구:
파이프 렌치재료
7- 1 valve box플레이스홀더
- 2 개플레이스홀더
- 2 socket and nipple플레이스홀더
- 2 bent clips플레이스홀더
- 1 short length플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
이 블루프린트로 만드는 것
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.