협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

작성자

Forge

13. 11월 2026NO
6
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
중급
8-15 minutes a pair, once practised

안내

1

Bar length and sizes

Jupyter 노트북 불러오는 중…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

이 단계의 재료:

연철 봉연철 봉1 개

필요한 도구:

줄자줄자
연필연필
두꺼운 종이두꺼운 종이
대장간 화덕대장간 화덕
모루용 절단 정모루용 절단 정
대장간 집게대장간 집게
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

필요한 도구:

대장간 화덕대장간 화덕
부리 모루부리 모루
썰매썰매
둥글리기 망치둥글리기 망치
대장간 집게대장간 집게
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

필요한 도구:

부리 모루부리 모루
둥글리기 망치둥글리기 망치
대장간 집게대장간 집게
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

필요한 도구:

부리 모루부리 모루
풀러 (홈 내는 쇠)풀러 (홈 내는 쇠)
썰매썰매
둥글리기 망치둥글리기 망치
대장간 집게대장간 집게
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

필요한 도구:

부리 모루부리 모루
열간 펀치열간 펀치
편자 못구멍 펀치편자 못구멍 펀치
둥글리기 망치둥글리기 망치
대장간 집게대장간 집게
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

필요한 도구:

대장간 화덕대장간 화덕
부리 모루부리 모루
둥글리기 망치둥글리기 망치
풀러 (홈 내는 쇠)풀러 (홈 내는 쇠)
열간 펀치열간 펀치
편자 못구멍 펀치편자 못구멍 펀치
대장간 집게대장간 집게
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

재료

1
  • 플레이스홀더

필요 도구

12

이 블루프린트로 만드는 것

CC0 퍼블릭 도메인

이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.

제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.

토론

(0)

로그인 하여 토론에 참여하세요

댓글 로딩 중...