
Making Deer Jerky and Pemmican — Preserving Venison for Survival
Jerky and pemmican are the two oldest methods of preserving venison for long-term storage without refrigeration. Jerky — thin strips of lean meat dried by sun, wind, or low heat — has been made by every hunting culture on earth. Pemmican takes jerky one step further: the dried meat is pounded to a powder, mixed with rendered tallow and dried berries, and packed into dense, calorie-rich bars that can last years without spoiling.
Pemmican was the strategic food supply of the North American fur trade, Arctic expeditions, and Plains nations for centuries — lightweight, calorie-dense (roughly 3,500 kcal per kg), and nutritionally complete. This blueprint covers the full process from fresh venison to finished pemmican.
안내
Select and trim the venison
Select and trim the venison
Use lean cuts — hindquarter rounds, backstrap, or eye of round. Trim away all visible fat, sinew, and silver skin. Fat goes rancid quickly and ruins dried meat. You need about 2 kg of trimmed lean meat to produce roughly 500 g of finished jerky.
이 단계의 재료:
Deer1 개필요한 도구:
Sharp KnifeSlice into thin strips
Slice into thin strips
Partially freeze the meat for 1-2 hours to firm it up for clean slicing. Cut with the grain into strips 3-5 mm thick, 2-3 cm wide, and as long as possible. Cutting with the grain makes chewy jerky; cutting against the grain makes more tender strips. Uniform thickness ensures even drying.
필요한 도구:
Sharp KnifeSalt the strips
Salt the strips
Rub coarse salt into both sides of each strip — about 20 g of salt per kg of meat. Salt draws moisture out and inhibits bacterial growth during the drying process. For flavoured jerky, add cracked black pepper or crushed dried herbs at this stage. Lay strips flat and let them cure for 1-2 hours.
이 단계의 재료:
Coarse Sea Salt40 gDry the strips
Dry the strips
Hang strips on a drying rack in direct sun and wind (traditional method, 1-3 days), or place on racks over a low fire or in an oven at 60-70°C for 6-10 hours. The jerky is done when it bends and cracks but does not snap in half — still flexible, but no moisture beads when squeezed. Overdrying makes it brittle; underdrying risks spoilage.
필요한 도구:
Drying Rack (Well-Ventilated)Pound the jerky into powder for pemmican
Pound the jerky into powder for pemmican
Break finished jerky into small pieces and pound in a stone mortar and pestle (or between two flat rocks) until it becomes a dry, shredded powder. The finer the powder, the better the pemmican binds. This is the base — dried lean protein with virtually no moisture left.
필요한 도구:
Stone Mortar and Pestle (large)Render the deer tallow
Render the deer tallow
Chop the reserved deer fat (from trimming in step 1) into small pieces and heat slowly in a pot over low fire until the fat melts completely and the solid bits (cracklings) float and turn golden. Strain through cloth to remove solids. The clear liquid fat is rendered tallow — it solidifies at room temperature and is the binding agent and calorie source in pemmican.
이 단계의 재료:
Animal Fat (Tallow)500 gMix pemmican
Mix pemmican
Combine the pounded jerky powder with warm (not hot) rendered tallow at roughly a 1:1 ratio by weight. Add a handful of dried berries (blueberries, cranberries, or saskatoon berries) for flavour and vitamin C. Mix thoroughly until the tallow coats all the meat fibres and the mixture holds together when pressed. Pack tightly into balls, bars, or pouches.
이 단계의 재료:
Blueberries100 gStore the pemmican
Store the pemmican
Wrap pemmican bars in cloth or pack into rawhide containers (parfleche). Stored in a cool, dry place, pemmican keeps for months to years — the rendered tallow seals out moisture and air, and the salt-cured, fully dried meat resists bacterial growth. This was the primary travel and emergency food of Plains nations, fur traders, and Arctic explorers for centuries.
재료
4- 40 g플레이스홀더
- 500 g플레이스홀더
- 100 g플레이스홀더
필요 도구
3- 플레이스홀더
연결된 블루프린트 재료
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.