협업

예술

뷰티 및 웰니스

공예

문화 및 역사

엔터테인먼트

환경

음식 및 음료

역공학

과학

스포츠

기술

웨어러블

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)

H. S. Bell · Public domain in the US (published 1923)

작성자

Forge

4. 11월 2026

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)

An above-ground oil tank of riveted 'tank steel': a flat bottom, rings of plate lapped and riveted, angle irons at top and bottom, and a self-supporting globe roof. Every seam is caulked oil-tight and the tank is water-tested before painting. Variable: capacity. Bell's Fig. 158 is 1,000 barrels: 20 ft inside diameter, about 20 ft 3 in high, four rings of 1/4 in plate, sixteen 3/16 in roof plates rising 3 ft. Standard tanks run from 500 to 80,000 barrels (120 ft x 40 ft). Source: H. S. Bell, American Petroleum Refining (1923), pp. 286-306. Picture: Fig. 158 of the book.

전문가

Unknown

안내

Choose the size and plates

Pick the capacity from the standard sizes (1,000 barrels: 20 ft diameter, 20 ft high). Take plate thickness from Bell's chart for the head and diameter, with a factor of safety of at least 2 1/2 for refinery tanks. Use at least 1/4 in for the shell; bottom 1/4 in on larger tanks, 3/16 in on smaller. Rings are 6 ft (72 in plates); about 7 ft is the limit.

필요한 도구:

알 수 없는 치수

Prepare the ground

Level the ground in a circle 10 ft wider than the tank and remove all vegetable growth. Avoid a mix of cut and fill. In old yards filled with cinders, dig them out at least 8 in deep and replace with fine gravel, loam or sand. On poor soil, use piles.

이 단계의 재료:

자갈1 as needed

필요한 도구:

알 수 없는 치수

Punch and scarf the plates

Punch the rivet holes. For 1/4 in plate with 5/8 in rivets, a single lap seam has holes 2 1/4 in apart and 1 1/8 in from the edge; keep the clear space between holes no more than 6 or 7 times the plate thickness, or the caulked edge springs. Scarf the corner of the middle plate where three plates meet: cold up to 1/4 in, hot above, drawn to an edge no thicker than 1/16 in.

필요한 도구:

펀치 프레스

큰 망치

Build the bottom on horses

Lay, rivet and caulk the bottom on trestles or horses about 30 in high. Rivet the bottom angle iron (Fig. 158: 3 x 3 x 5/16 in) with a 1/4 in bent-plate shoe behind each angle splice; caulk the shell leg past the shoe at least 12 in, or better bevel and caulk the angle all round. Assemble and drive the first ring while the bottom is still up. Test the bottom under 6 to 8 in of water. Coat its underside with ship-bottom or heavy asphalt paint.

이 단계의 재료:

연강판1 bottom, first ring

연강 앵글1 bottom angle

강철 리벳1 개

알 수 없는 재료1 asphalt paint

필요한 도구:

리벳 망치

구멍 넓힘 드리프트

물

넓은 붓

Lower it and raise the shell

Raise the tank on jacks round the edge, clear out the horses and debris, and lower the bottom to grade. Rivet and caulk the remaining rings from scaffolds: floating scaffolds where water is at hand (water is pumped in as each ring is caulked tight, testing as you go), or brackets bolted through punched holes, later plugged with hot rivets. Where three plates meet, bolt them, heat cherry red with an oil-burning torch and lay the joint up with sledges before riveting. Fit the top angle (2 1/2 x 2 1/2 x 5/16 in) and a flanged steel manhole in the bottom ring.

이 단계의 재료:

연강판1 rings

연강 앵글1 top angle

강철 리벳1 개

필요한 도구:

나사 잭

리벳 망치

구멍 넓힘 드리프트

횃불

큰 망치

물

Fit the globe roof

For tanks up to 54 ft across, rivet on a self-supporting globe roof of segmental 3/16 in plates (Fig. 158: sixteen plates, 1/4 in centre plate, 3 ft rise); cold riveting is fine here. Make it gas-tight, with one vent at the apex covered by brass or monel wire cloth of at least 50 mesh.

이 단계의 재료:

연강판1 roof

강철 리벳1 개

필요한 도구:

리벳 망치

Test and paint

Fill the tank with water to test it before painting; it shows the important leaks, though not always tightness for light oils. Wire-brush off mill scale and rust. Give shell and roof three coats: one of red lead ground in boiled linseed oil, then two of good grey graphite paint.

이 단계의 재료: