협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)
A flat screwdriver is a steel shank flattened to a blade that fits the slot of a screw. H. Holford's 20th Century Toolsmith and Steelworker (1907) says most smiths make them so they twist or break on a hard screw, and gives his cure: forge it from 75-point carbon steel, strike the blade a few good blows on each flat at a low heat, harden it and let the temper run to grey.
His Fig. 60 shows the shape without its handle. He gives no sizes and no handle, which are unknown here; the brine bath is from his chapter on the hardening bath.
Source: H. Holford (1907), pp. 21, 118. Picture: his Fig. 60.
중급
Half a day
안내
1
1
Read Holford
Read Holford
"Strike it a few good blows on each flat side of the screw driving edge while at a low heat. Then harden and allow the temper to draw to a grey, cool off and you will have a screw driver that will give unlimited satisfaction."
2
2
Forge the shape
Forge the shape
Take good steel of 75 points carbon. Forge it to the shape of Fig. 60: a round shank, flattened at one end to the driving blade and drawn to a pointed tang at the other for the handle. Holford gives no sizes (unknown).
이 단계의 재료:
공구강 사각봉1 bar필요한 도구:
단조 화덕
모루
대장간 망치
대장간 집게
알 수 없는 치수
보안경
내열 장갑3
3
Pack the blade
Pack the blade
At a low heat, strike a few good blows on each flat side of the driving edge.
필요한 도구:
대장간 망치모루단조 화덕대장간 집게4
4
Harden and temper grey
Harden and temper grey
Heat the blade end evenly and quench it in the hardening bath. Holford's bath is clean water free from grease, best made into a brine with as much salt as the water will dissolve, kept as large and as cold as possible. Brighten the blade with a file so the colours show, draw the temper to a grey, then cool it off.
필요한 도구:
단조 화덕
포화 소금물대장간 집게
고운 쇠줄내열 장갑5
5
Fit a handle
Fit a handle
Fit a handle on the tang. Holford shows the screwdriver without one and does not say what it is made of (unknown).
이 단계의 재료:
알 수 없는 재료1 handle6
6
History and honest limits
History and honest limits
Holford, a toolsmith writing for blacksmiths and tool dressers, says a good screwdriver is prized by every mechanic, woodworkers most of all, yet few smiths could make one that would not break or twist. His temper table lists the screwdriver at grey, in 0.75 carbon steel.
He gives no sizes, no handle and no heat for hardening; those are unknown here, and the tools are ours.
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.