협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Shaded Forge Goggles: Ventilated Eye Cups with a Coloured and a Clear Lens (Tully, US 1,679,105)
Molten metal and glass give off a strong glare, and goggles worn over hot work steam up.
George L. Tully and Solomon Lacasse of the American Optical Company (filed 1927, US 1,679,105) made goggles for welders and "those employed in handling molten metal, glass and similar products": hard-rubber or Bakelite eye cups with a coloured inner lens against the glare and a cheap clear outer lens that is easily replaced, held apart by a crimped spring under a bayonet cap. Slots let air through between the lenses and inside the cup, so the lenses do not steam up.
This rung turns the eye cups from ebonite, cuts the lenses and assembles the goggles. Not given: any size, the metal of the cap, spring and chain, the band's material and the shade of the coloured glass.
Source: G. L. Tully and S. Lacasse, US 1,679,105 (1928). Picture: the patent's Figs. 1-4.
중급
About 6 hours
안내
1
1
Read US 1,679,105
Read US 1,679,105
"The inner lens being preferably of colored glass to reduce the glare from the molten material and the outer lens being of plain glass. Colored glass is expensive, whereas the outer plain glass is cheap and economical. If the outer glass is broken it can be easily replaced, or if it becomes scratched or marred so as to become semi-opaque a new lens can be quickly and easily inserted for the old one."
2
2
Turn the eye cups
Turn the eye cups
Turn two annular eye cups from ebonite (hard rubber, one of his two materials) on the lathe. Inside each, leave a shouldered flange near the front to carry the inner lens. Cut the eye side of the cup on an angle and shape it to fit the face. Saw two slots opposite each other through the wall in front of the flange, between the lenses, and two more behind the flange for air between the inner lens and the eye. The sizes are ours.
이 단계의 재료:
에보나이트 봉1 as required필요한 도구:
금속 선반
선반 공구 세트 (HSS)
쇠톱(핵소)
정밀 줄(니들 파일) 세트
보안경3
3
Cut the lenses
Cut the lenses
For each cup, cut a round inner lens from coloured glass and a round outer lens from plain glass to fit the cup, and grind their edges smooth.
이 단계의 재료:
색유리 판2 개
유리판2 개필요한 도구:
유리 칼
연삭 숫돌바퀴보안경4
4
Make the caps, springs and shields
Make the caps, springs and shields
For each cup make an annular cap that fits over the cup's front flange, with two bayonet slots in its lower edge and two slots opposite each other that line up with the cup's front slots. Crimp a ring of thin metal into a wave to sit between the lenses. Bend a shield closed on three sides and open at the bottom to cover one of the rear slots, and rivet it to the cup.
이 단계의 재료:
알 수 없는 금속1 as required필요한 도구:
판금 가위정밀 줄(니들 파일) 세트
탁상 드릴
리벳 공구 한 벌
볼핀 해머5
5
Fit the lenses
Fit the lenses
Drop the coloured lens onto the cup's flange, lay the crimped spring on it, then the clear lens, and slide the cap on so its bayonet slots pass over two stud screws in the cup. Turn the cap and tighten the screws. The spring lets the outer lens yield if it is struck. To change a lens, loosen the screws, slide the cap back and push the lenses out from inside.
이 단계의 재료:
기계 나사4 개필요한 도구:
드라이버 세트탁상 드릴6
6
Bridge and band
Bridge and band
Join the two cups with a short chain covered with rubber tubing. Fix an elastic head band to the outer sides of the cups with an adjustable buckle.
이 단계의 재료:
알 수 없는 금속1 as required
고무관1 as required
알 수 없는 재료1 as required
혀가 달린 황동 버클1 개필요한 도구:
드라이버 세트7
7
The patent drawing
The patent drawing
US 1,679,105, Figs. 1-4: the goggles (1), a cup from the side with the shield (2), a section through cup, lenses and cap (3) and a section through the lenses and spring (4). Public domain (expired patent).
8
8
History and honest limits
History and honest limits
Tully and Lacasse filed on 16 May 1927 for the American Optical Company of Southbridge, Massachusetts; the patent was granted on 31 July 1928.
The patent gives no sizes and no shade for the coloured glass, so our goggles are not rated to any welding or furnace filter standard; do not rely on them for electric-arc welding. The cap, spring, chain and shield metal and the band's elastic material are not named (unknown).
재료
8- 1 as required플레이스홀더
- 2 개플레이스홀더
- 2 개플레이스홀더
- 1 as required플레이스홀더
- 4 개플레이스홀더
- 1 as required플레이스홀더
- 1 as required플레이스홀더
- 1 개플레이스홀더
이 블루프린트로 만드는 것
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.