예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Cushioned Ticket Punch: A Spring That Strips the Ticket and Rings That Carry the Joint
A conductor punching hundreds of tickets a day needs the ticket to come off the punch by itself and a joint that does not work loose.
Jacob Beck of Philadelphia received US 68,687, dated 10 September 1867, for a conductor's ticket-punch with "a spiral spring enclosed in a rubber cushion or pad, having a metallic disk on its upper side, forming a rest for the tickets", a coil spring "concealed in the joint, yet readily accessible", and a joint carried on two concentric flanges: "Nearly all the friction of the joint will be on the flanges f g".
This rung works out the load on a bare pin against Beck's rings, then fits a spring-and-rubber stripper to a hand punch and counts stuck tickets before and after.
중급
About 2 hours
안내
1
1
Joint load on a pin and on rings
Joint load on a pin and on rings
Jupyter 노트북 불러오는 중…
2
2
How a punch cuts
How a punch cuts
The embedded blueprint explains punch, die and clearance. Beck's punch is the same cut; his changes are to the stripper and the joint.
3
3
Read US 68,687
Read US 68,687
"Surrounding the stripper is a spiral spring, C, which is enclosed in a flexible pad or cushion, D. The lower end of the spiral spring is firmly secured to the jaw, and its other end is united to a disk, E, of metal or other suitable material, having a central perforation, through which the stripper will protrude."
"When the conductor has punched the ticket and releases the handles from pressure, the jaws will immediately open, and the springs c d assuming their original position will force the ticket upwards as the stripper moves with its jaw and returns to its place below the disk E, thus entirely freeing the ticket, allowing its withdrawal without any impediments from the stripper."
4
4
Fit the stripper and punch tickets
Fit the stripper and punch tickets
Take a single-hole plier punch. Cut a ring of rubber sheet 5 mm thick to sit round the punch's pin on the jaw, with a hole a little larger than the pin. Seat a small compression spring inside the ring round the pin, and glue a washer on top as Beck's disk, so the pin passes through its hole when the handles close.
Cut 100 tickets 5 × 3 cm from card stock. Punch 50 with the punch as bought and count how many stay on the pin and have to be pulled off. Fit the cushion and punch 50 more; count again. Punch a card of double thickness once each way and note whether it strips.
이 단계의 재료:
고무 시트1 개
압축 스프링 세트1 개
평와셔1 개
콘택트 시멘트2 ml
카드지1 개필요한 도구:
펀치(종이 구멍 뚫개)
공예용 칼
가위
디지털 캘리퍼스 6인치
자5
5
A punch that holds the ticket, tears it or jams
A punch that holds the ticket, tears it or jams
Cushioned ticket punch troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Jacob Beck** of Philadelphia signed US 68,687 on 14 May 1867; it is dated 10 September 1867. The screw-pin of his joint was "merely intended for holding the two parts of the punch together", and the jaws and handles were cut away to fit the circle of the joint, with shoulders limiting how far the jaws open. His six claims cover the bearing rings, the enclosed coil spring, the seat, the stripper's spring and the pad.
**Honest limits.** A bought plier punch with a fitted rubber ring, spring and washer stands in for Beck's punch; the ringed joint is not rebuilt. The notebook treats the pin's load as spread over its projected area; its sizes are examples. Your counts are the result.
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.