예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop
A bath brush fed from a hose runs all the time, or needs a tap out of reach.
Daniel S. Koons and William F. Moughler of Chicago received US 634,527, dated 10 October 1899, for "a fountain bath-brush": a false back with a water passage, joined to the brush by a hollow screw whose perforated head lets the water out among the bristles, with a valve that a spring and the water pressure hold shut until a finger presses its stem, and a strap that holds the hand to the brush.
This rung works out the finger force, then builds the false back on a scrub brush with a tyre valve as the finger valve, and measures the force and the flow.
중급
About 3 hours
안내
1
1
Force to open the valve
Force to open the valve
Jupyter 노트북 불러오는 중…
2
2
A brush that feeds itself before it
A brush that feeds itself before it
The embedded blueprint feeds soap from inside a shaving brush. Koons and Moughler feed water, and give the finger a valve to start and stop it.
3
3
Read US 634,527
Read US 634,527
"Said valve is held normally closed by means of a spring 9 and also by the water-pressure, as will be obvious."
"A strap k is secured at the sides of said back B' and passes over the latter, so that by inserting the hand between said back B' and said strap k the brush can be firmly held and the fingers at the same time kept in position to operate the valve."
4
4
Bore the false back
Bore the false back
Cut a hardwood block 120 × 50 × 22 mm. Drill a 6 mm passage 90 mm along its centre from one end, and a 6 mm hole down from the top to meet it 30 mm from the far end.
이 단계의 재료:
경목 블록1 개필요한 도구:
바이스(만력)
무선 드릴
브래드 포인트 드릴 비트 세트
자
투명 보안경5
5
Fit the finger valve
Fit the finger valve
Drill a hole across the passage 20 mm from the inlet to take a tyre valve, pin upward. Epoxy it in so the water must pass through it.
이 단계의 재료:
타이어 밸브1 개
2액형 에폭시1 개필요한 도구:
무선 드릴
드릴 비트 세트6
6
Join it to the brush
Join it to the brush
Drill a 6 mm hole through the scrub brush's back to line up with the outlet. Cut a rubber gasket, and screw the block on with four wood screws.
이 단계의 재료:
솔(억센 털)1 개
고무 시트1 개
#8 × 1인치 나무 나사1 개필요한 도구:
무선 드릴드릴 비트 세트
공예용 칼
드라이버 세트7
7
Strap and hose
Strap and hose
Screw a strip of rubber sheet across the block as a hand strap, over the valve's side. Fit a hose connector to the inlet with brass fittings and PTFE tape.
이 단계의 재료:
고무 시트1 개#8 × 1인치 나무 나사1 개
황동 피팅1 개
PTFE 나사 밀봉 테이프1 개필요한 도구:
드라이버 세트
멍키스패너8
8
The patent drawing
The patent drawing
US 634,527 drawing sheet, public domain (expired patent).
9
9
Measure force and flow
Measure force and flow
Connect the garden hose and turn on the tap. Press the valve pin with the force meter's hook until water runs; note the force. Hold it open over the jug for 30 s and read the flow.
이 단계의 재료:
정원용 호스1 개
물1 개필요한 도구:
힘 측정기(스프링 저울)
계량 저그
스톱워치10
10
A valve that drips, sticks or barely flows
A valve that drips, sticks or barely flows
Finger-valve bath brush troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Daniel S. Koons** and **William F. Moughler** of Chicago filed US 634,527 on 21 September 1898; it is dated 10 October 1899. They called it a self-cleansing brush. Its handle is telescopic, with a stuffing-box between the two members, and the hose can be led through it to the brush; a second form uses a nozzle as the screw joining the backs. They did not limit it to the bath.
**Honest limits.** A tyre valve stands in for their seated valve and stem, and wood screws for their hollow screw. Your forces and flows are the result.
재료
10- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 플레이스홀더
- 1 개플레이스홀더
- 플레이스홀더
- 정원용 호스10% 수수료1 개플레이스홀더
- 1 개플레이스홀더
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.