예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Free-Spindle Ticket Punch: A Loose Spindle Lifted by a Spring, Close to the Pivot
A punch whose spindle hangs on a small pivot breaks there, and cannot be set close to the levers' joint where the squeeze is strongest.
Warren Hill of Springfield, Massachusetts, received US 79,470, dated 30 June 1868, antedated 5 May 1868, as "an improvement upon the invention of the said William J. Phelps". His spindle is not attached to either lever: it slides in a cylindrical guide, a plate fixed to it projects into a recess over a spiral spring that raises it, and lever A bears on its rounded top. "By this construction I am enabled to place the die-spindle nearer the fulcrum of the levers, and also cause the lever A to bear wholly upon the extreme end of the die-spindle C, and thus increase the power of the punch to perforate the thicker board or paper tickets." Springs on stems at the levers' ends open them and serve as a finger loop, and the stems act as stops.
This rung works out the gain from moving the spindle toward the pivot, with a work check, then makes the punch with a free, spring-lifted spindle and punches card of two thicknesses.
고급
About 6 hours
안내
1
1
Closer to the pivot
Closer to the pivot
Jupyter 노트북 불러오는 중…
2
2
The punch it improves
The punch it improves
The embedded blueprint pivots the spindle to one lever. Hill frees it, lifts it with a spring, and sets it nearer the fulcrum.
3
3
Read US 79,470
Read US 79,470
"To raise the die-spindle when the levers are opened again, I attach the projecting plate e rigidly to the side of the spindle, which has a circular portion and a neck, which enters the spindle, and is fastened securely therein; or I may form the die-spindle C and its projection e in one piece, or from one piece of metal. Beneath this circular plate e, I form a recess, f′, in B, and insert a spiral spring, f, the upper end of which bears against the plate, and tends to raise the die-spindle."
"I am aware that a device has been used as a ticket-punch, as shown in Letters Patent granted to William J. Phelps, and dated September 17, 1867; but my device differs from that very materially in its construction, inasmuch as said Phelps's device has a spindle which is pivoted to one lever by a small pivot, which is liable to breakage"
4
4
Make the punch and try thick card
Make the punch and try thick card
**Levers.** Cut two levers from flat bar, A with a semicircular ear at its end and B with cheeks to take it, and join them with a screw b as the pivot. Saw a ticket slot h across B's jaw close to the pivot.
**Guide, die and spindle.** Drill a guide j through B above the slot, set a hardened die plate below it with a slightly conical opening g underneath, and file a 5 mm rod as the spindle with a rounded top i. Solder a small washer to its side as the plate e.
**Spring.** Drill a recess f′ in B beside the guide, put a short spring in it under the washer, and file a recess c′ in A that bears on the spindle's top.
**Opening spring and stops.** Turn a stem m down from each lever's end and fit one long spring over both stems, so it opens the levers and makes the finger loop; leave the stems long enough to stop the levers just as the spindle meets the die.
**Test.** Punch thin card and then card twice as thick, reading the squeeze with the spring scale. Compare with the pivoted-spindle punch.
이 단계의 재료:
연강 평강0.35 미터
연강 환봉0.1 미터
연강판1 개
평와셔1 개
무연 배관 땜납1 개
플럭스1 개
압축 스프링 세트1 개
기계 나사1 개
카드지1 개필요한 도구:
쇠톱(핵소)
줄 (손줄)
정밀 줄(니들 파일) 세트
바이스(만력)
무선 드릴
드릴 비트 세트
프로판 토치
인두
힘 측정기(스프링 저울)
디지털 캘리퍼스 6인치
가죽 작업 장갑
투명 보안경5
5
A punch whose spindle sticks, jumps or stops short
A punch whose spindle sticks, jumps or stops short
Free-spindle ticket punch troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Warren Hill** of Springfield, Hampden County, Massachusetts, received US 79,470, dated 30 June 1868, antedated 5 May 1868; J. P. Buckland witnessed it, as he had Phelps's. His levers were pivoted at the end with a semicircular ear on A entering cheeks on B, secured by the screw b; a projection b′ on A met a part g′ on B to limit opening; and a collar on the spindle with the spring round it could replace the side plate. His claim is the spindle C, projection e and spring f with the recessed lever A and slotted lever B.
**Honest limits.** Filed flat bar, a soldered washer and bought springs stand in for his made parts. The notebook ignores friction; its forces and lengths are examples. Your punched card is the result.
재료
9- 0.35 미터플레이스홀더
- 0.1 미터플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.