협업
예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
중급
Unknown
안내
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
이 단계의 재료:
물푸레나무 판재1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in필요한 도구:
손톱(핸드소)
손대패
양손 대패2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
이 단계의 재료:
화이트 오크 판재1 개
나무 다월1 3/16 in pins필요한 도구:
등대기톱
장부구멍 끌
그므개(마킹 게이지)
곡병 손드릴과 비트
각도자3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
이 단계의 재료:
화이트 오크 판재1 legs 1 1/2 in square, stays
둥근머리 볼트4 3 in필요한 도구:
손톱(핸드소)곡병 손드릴과 비트
드라이버 세트4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
이 단계의 재료:
소나무 판재1 1/2 in bottom, 5/8 in sides
유화 물감1 개필요한 도구:
손톱(핸드소)손대패
붓 세트5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
이 단계의 재료:
소나무 판재1 3/4 in front board
쇠못1 1 1/2 in cut nails
연강 평강1 7/8 in hoop iron
나사못1 3/4 in round-headed유화 물감1 개필요한 도구:
손톱(핸드소)
망치드라이버 세트붓 세트6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
이 단계의 재료:
물푸레나무 판재1 axle and felloes화이트 오크 판재1 spokes
철 환봉1 3/8 in pins나무 다월4 1/4 in연강 평강1 3/4 x 1/8 in tyre필요한 도구:
목선반양손 대패곡병 손드릴과 비트망치7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
이 단계의 재료:
연강 평강2 3/4 x 1/8 in irons나사못1 개유화 물감1 개필요한 도구:
드라이버 세트붓 세트재료
10- 1 axle and felloes플레이스홀더
- 1 spokes플레이스홀더
- 4 1/4 in플레이스홀더
- 4 3 in플레이스홀더
- 1 3/4 in front board플레이스홀더
- 3 개플레이스홀더
- 1 1 1/2 in cut nails플레이스홀더
- 2 3/4 x 1/8 in irons플레이스홀더
- 1 개플레이스홀더
- 1 3/8 in pins플레이스홀더
이 블루프린트로 만드는 것
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.