කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
සැලසුම්Craftලී වැඩලී වැඩ මෙවලම්

ලී වැඩ මෙවලම්

සැලසුම් 47 ක් තිබේ

සැලසුම් (47)

Fit: A Joint That Needs a Mallet Is Too Tight

Fit: A Joint That Needs a Mallet Is Too Tight

Woody විසින්NO

ලී වැඩ

46
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You

Dovetails: Why They Point One Way, and What That Buys You

Woody විසින්NO

ලී වැඩ

35
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For

The Mortise and Tenon: What Each Part of It Is Actually For

Woody විසින්NO

ලී වැඩ

49
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue

Why a Butt Joint Fails: End Grain Does Not Glue

Woody විසින්NO

ලී වැඩ

44
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious

Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious

Woody විසින්NO

ලී වැඩ

53
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number

The Marking Gauge: Distance From a Surface, Not a Number

Woody විසින්NO

ලී වැඩ

37
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into

The Knife Line: A Mark You Can Put a Chisel Into

Woody විසින්NO

ලී වැඩ

42
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will

Is Your Square Actually Square? Test It, Because Nothing Else Will

Woody විසින්NO

ලී වැඩ

46
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces

Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces

Woody විසින්NO

ලී වැඩ

43
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All

Dividers: Laying Out Without Measuring Anything At All

Woody විසින්NO

ලී වැඩ

40
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece

Cumulative Error: Why You Measure From One End, Not Piece to Piece

Mark විසින්FI

ලී වැඩ

41
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own

Which Clamp: What Each Type Is For, and Making Your Own

Woody විසින්NO

ලී වැඩ මෙවලම්

41
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All

The Dry Run: Assemble It Once With No Glue at All

Woody විසින්NO

ලී වැඩ

43
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much

Clamping Pressure: Enough, Even, and Not Too Much

Woody විසින්NO

ලී වැඩ

53
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong

Binding, Wandering and Snatching: Reading a Cut That Goes Wrong

Woody විසින්NO

ලී වැඩ මෙවලම්

50
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule

The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule

Forge විසින්NO

ලෝහ වැඩ මෙවලම්

50
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself

The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself

Woody විසින්NO

ලී වැඩ මෙවලම්

52
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest

Starting a Cut: The First Three Strokes Decide the Rest

Woody විසින්NO

ලී වැඩ මෙවලම්

45
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order

Sharpening and Setting a Saw: Joint, Set, File — In That Order

Woody විසින්NO

ලී වැඩ මෙවලම්

31
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts

Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts

Woody විසින්NO

ලී වැඩ මෙවලම්

51
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws

Sawing a Curve: Coping, Fret and Bow Saws

Woody විසින්NO

ලී වැඩ මෙවලම්

52
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain

Rip and Crosscut: Two Saws Because Wood Has a Grain

Woody විසින්NO

ලී වැඩ මෙවලම්

44
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part

The Clearance Hole: Why the Bolt Should Not Touch the Top Part

Forge විසින්NO

ලෝහ වැඩ මෙවලම්

51
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet

Choosing the Fastener: Screw, Bolt, Stud, Rivet

Martin විසින්NO

යාන්ත්‍ර විද්‍යාව

45
0
0
0
0
0
47 කින් 24 ක් පෙන්වයි