කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Coopered Vat: Oak Staves in Riveted Iron Hoops
Woody

නිර්මාතෘ

Woody

14. ඔක්තෝබර් 2026NO
7
0
0
0
0

Coopered Vat: Oak Staves in Riveted Iron Hoops

A vat is the cooper's large open tub: oak staves standing edge to edge, held tight by hoops, with a flat bottom set in a groove. Coopers made the vats beer was brewed in; papermakers and chemists use them to hold pulp, washes and settling liquors. Shave tapered staves, forge and rivet iron hoops, raise the staves in the hoops and fit the bottom. The picture: our diagram, a vat and its tapered staves.
උසස්
Several days

උපදෙස්

1

Shape the staves

Rive or saw oak into staves as long as the vat is deep. Shave each one on the horse, taper it from top to bottom (step 5 gives the widths), and plane the edges so neighbours meet along their whole length.

මෙම පියවර සඳහා ද්‍රව්‍ය:

දැඩි දැව ඝන පලංචියදැඩි දැව ඝන පලංචිය6 කැබලි

අවශ්‍ය මෙවලම්:

ෆ්‍රෝ (පලන පිහිය)ෆ්‍රෝ (පලන පිහිය)
සූරන බංකුවසූරන බංකුව
අත් දෙකේ ඇදුම් පිහියඅත් දෙකේ ඇදුම් පිහිය
අත් ලීයන යන්ත්‍රයඅත් ලීයන යන්ත්‍රය
අත් කියතඅත් කියත
2

Forge the hoops

Draw wrought iron into flat strip about 30 × 3 mm (our size), cut it to the circumference where each hoop sits plus a lap, bend it round, punch the lap and rivet it closed.

මෙම පියවර සඳහා ද්‍රව්‍ය:

තලන ලද යකඩ දණ්ඩතලන ලද යකඩ දණ්ඩ3 කැබලි
යකඩ රිවට්යකඩ රිවට්6 කැබලි
අඟුරුඅඟුරු5 as required

අවශ්‍ය මෙවලම්:

කම්මල් උදුනකම්මල් උදුන
නියන (ඇන්විලය)නියන (ඇන්විලය)
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
උණුසුම් සිදුරු කරන මෙවලමඋණුසුම් සිදුරු කරන මෙවලම
කම්මල්කරුගේ අඬුවකම්මල්කරුගේ අඬුව
වෑල්ඩින් අත්වැසුම්වෑල්ඩින් අත්වැසුම්
3

Raise the vat

Stand the staves inside a hoop, wide ends up, until the ring is closed. Drive the hoops down with a hammer and a block until the joints close tight.

අවශ්‍ය මෙවලම්:

හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
4

Groove and bottom

Cut a groove round the inside a little above the lower edge. Join planks into a board, scribe a circle to fit the groove, cut and bevel it, slack the lower hoop, spring the bottom in, and drive the hoop home. Fill with water: the wood swells and seals.

මෙම පියවර සඳහා ද්‍රව්‍ය:

දැඩි දැව ඝන පලංචියදැඩි දැව ඝන පලංචිය2 කැබලි

අවශ්‍ය මෙවලම්:

නියන් කට්ටලයනියන් කට්ටලය
තුඩු දෙකේ මිනුම් කවකටුවතුඩු දෙකේ මිනුම් කවකටුව
අත් කියතඅත් කියත
අත් ලීයන යන්ත්‍රයඅත් ලීයන යන්ත්‍රය
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
5

Staves and hoops

Jupyter සටහන් පොත පූරණය වෙමින්…

ද්‍රව්‍ය

4

අවශ්‍ය මෙවලම්

13

සම්බන්ධ බ්ලූප්‍රින්ට්

මෙම බ්ලූප්‍රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්‍රම, ද්‍රව්‍ය හෝ මූලධර්ම

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...