සහයෝගීතාව
කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
Penny

නිර්මාතෘ

Penny

2. නොවැම්බර් 2026DK
6
0
0
0
0

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)

The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight. Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit. Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
උසස්
2 weeks

උපදෙස්

1

Build the magnet circuit

Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.

මෙම පියවර සඳහා ද්‍රව්‍ය:

කුඩා චුම්බකයකුඩා චුම්බකය1 column
වට යකඩ දණ්ඩවට යකඩ දණ්ඩ1 soft iron core
නොදන්නා ලෝහයනොදන්නා ලෝහය1 housing and end caps
නොදන්නා ද්‍රව්‍යයනොදන්නා ද්‍රව්‍යය1 support plate, panel, base

අවශ්‍ය මෙවලම්:

ඉස්කුරුප්පු නියන කට්ටලයඉස්කුරුප්පු නියන කට්ටලය
නොදන්නා මිනුම්නොදන්නා මිනුම්
2

Hang the coil in the gap

Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.

මෙම පියවර සඳහා ද්‍රව්‍ය:

එනැමල් ආලේපිත තඹ කම්බියඑනැමල් ආලේපිත තඹ කම්බිය1 coil
නොදන්නා ද්‍රව්‍යයනොදන්නා ද්‍රව්‍යය1 bobbin, frames, cantilevers
තරාදි තැටියතරාදි තැටිය1 කැබැල්ල

අවශ්‍ය මෙවලම්:

නොදන්නා මිනුම්නොදන්නා මිනුම්
3

Fit the capacitor rings

Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.

මෙම පියවර සඳහා ද්‍රව්‍ය:

නොදන්නා ලෝහයනොදන්නා ලෝහය1 rings
අනුකලිත පරිපථයඅනුකලිත පරිපථය1 sensing circuit
සම්බන්ධක කම්බියසම්බන්ධක කම්බිය1 කැබැල්ල
පාස්සන ඊයම් කම්බියපාස්සන ඊයම් කම්බිය1 a little

අවශ්‍ය මෙවලම්:

පෑස්සුම් කූරුපෑස්සුම් කූරු
4

Close the servo loop and read the current

Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.

මෙම පියවර සඳහා ද්‍රව්‍ය:

අනුකලිත පරිපථයඅනුකලිත පරිපථය1 servo and counting circuits
ප්‍රතිරෝධයප්‍රතිරෝධය2 stable resistor, thermal resistor
විභව මානයවිභව මානය1 calibration
ඛණ්ඩ LCD පුවරුවඛණ්ඩ LCD පුවරුව1 display
පාස්සන ඊයම් කම්බියපාස්සන ඊයම් කම්බිය1 a little

අවශ්‍ය මෙවලම්:

පෑස්සුම් කූරුපෑස්සුම් කූරු
ක්‍රමාංකන බර කට්ටලයක්‍රමාංකන බර කට්ටලය

ද්‍රව්‍ය

12

අවශ්‍ය මෙවලම්

4

සම්බන්ධ බ්ලූප්‍රින්ට්

මෙම බ්ලූප්‍රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්‍රම, ද්‍රව්‍ය හෝ මූලධර්ම

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...