සහයෝගීතාව
කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Lead Came: Window Rods Cast in a Hinged Iron Mould (Theophilus, tr. Hendrie 1847)
Forge

නිර්මාතෘ

Forge

4. නොවැම්බර් 2026NO
5
0
0
1
0

Lead Came: Window Rods Cast in a Hinged Iron Mould (Theophilus, tr. Hendrie 1847)

The lead rods that hold the pieces of a medieval glass window, cast the way Theophilus describes around 1100: pure lead is poured with a warm iron spoon into a hinged iron mould with grooves hollowed down both halves, knocked out, and the mould closed again for the next. Kept at an even heat, one heating of the mould casts more than forty rods. Source: Theophilus, De Diversis Artibus, Book II, ch. XXIII-XXV, tr. R. Hendrie (1847), pp. 147-149. Picture: p. 149.
මධ්‍යම
Unknown

උපදෙස්

1

Make the iron mould

Take two irons two fingers broad, one finger thick and a yard long. Hinge them together at one end with a nail; make the other end a little wider and thinner to form the pouring mouth. File them until no light shows between them. Rule two lines down the middle of each, hollow the groove between them with a chasing iron as deep as you wish and rasp it a little, so that the lead poured in makes one piece.

අවශ්‍ය මෙවලම්:

ඊයම් තීරු අච්චුවඊයම් තීරු අච්චුව
2

Melt the lead

Make a hearth with a hollow for a large earthen vessel lined inside and out with clay beaten up with dung, and dry it with a big fire. Put pure lead on the fire over the vessel so that it runs into it as it melts.

මෙම පියවර සඳහා ද්‍රව්‍ය:

ඊයම් වාත්තු කැටයඊයම් වාත්තු කැටය1 pure lead

අවශ්‍ය මෙවලම්:

මැටි හැළියමැටි හැළිය
අඟුරුඅඟුරු
3

Cast the rods

Warm the open mould on the charcoal, close it and set it in the slot of a yard-long wooden holder standing on the ground. Pour the lead in with a small warmed iron spoon, keeping the spoon on the fire between pours. Knock the mould out, open it with a knife, take out the rod, close it and cast again. If the lead does not reach the bottom, warm the mould more. At an even heat you can cast more than forty rods.

අවශ්‍ය මෙවලම්:

ඊයම් තීරු අච්චුවඊයම් තීරු අච්චුව
විශාල හැන්ද (සුප් හැන්ද)විශාල හැන්ද (සුප් හැන්ද)
අත්කම් පිහියඅත්කම් පිහිය
අඟුරුඅඟුරු

ද්‍රව්‍ය

1

අවශ්‍ය මෙවලම්

5

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...