ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
මධ්යම
8
උපදෙස්
1
1
Harvest and clean long rye straw
Harvest and clean long rye straw
Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.
Materials for this step:
Rye Straw1 මිටියTools needed:
Knife2
2
Split and soak the binding cane
Split and soak the binding cane
Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.
Materials for this step:
Split Cane1 මිටිය
Water3 ලීටර්Tools needed:
Knife3
3
Make the girth gauge
Make the girth gauge
Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.
Tools needed:
Skep Girth Gauge4
4
Bind the crown
Bind the crown
Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.
Materials for this step:
Rye Straw1 මිටියSplit Cane1 මීටර්Tools needed:
Awl5
5
Feed straw into an even rope
Feed straw into an even rope
Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.
Materials for this step:
Rye Straw1 මිටියTools needed:
Skep Girth Gauge6
6
Sew the first coils to the crown
Sew the first coils to the crown
Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.
Materials for this step:
Split Cane1 මීටර්Tools needed:
Awl7
7
Spiral outward to start the dome
Spiral outward to start the dome
Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.
Materials for this step:
Rye Straw1 මිටියSplit Cane1 මීටර්Tools needed:
Awl8
8
Build the domed wall downward
Build the domed wall downward
Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.
Materials for this step:
Rye Straw1 මිටියSplit Cane1 මීටර්Tools needed:
AwlSkep Girth Gauge9
9
Keep the courses even
Keep the courses even
Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.
Materials for this step:
Rye Straw1 මිටියTools needed:
Awl10
10
Widen to the finished base
Widen to the finished base
As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.
Materials for this step:
Rye Straw1 මිටියSplit Cane1 මීටර්Tools needed:
Awl11
11
Cut the flight entrance
Cut the flight entrance
At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.
Tools needed:
Knife12
12
Finish and lock the base coil
Finish and lock the base coil
Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.
Materials for this step:
Split Cane1 මීටර්Tools needed:
Awl13
13
Trim the skep clean
Trim the skep clean
Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.
Tools needed:
Knife14
14
Clom the outside for weatherproofing
Clom the outside for weatherproofing
Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.
Materials for this step:
Cow Dung2 කිග්රෑ
Ball Clay1 කිග්රෑ15
15
Cure the finished skep
Cure the finished skep
Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.
ද්රව්ය
6- 1 මිටියස්ථානගත
- 6 මීටර්ස්ථානගත
Connected Blueprint Materials
සම්බන්ධ බ්ලූප්රින්ට්
මෙම බ්ලූප්රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්රම, ද්රව්ය හෝ මූලධර්ම
Building a Thatched Lean-To Shelter — Basic Wind and Rain Protection
Spartan විසින්
Wilderness
24
0
0
0
1
0
Egyptian Beeswax Candle — Making Beeswax Candles with Rush Wicks
YourGrandma විසින්
Biology
55
0
0
0
0
0
Honey as a Wound Dressing — The Oldest Antimicrobial Medicine Known to Humanity
Bob විසින්
Wilderness
31
0
0
0
3
0
CC0 පොදු වසම
මෙම බ්ලූප්රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.
බ්ලූප්රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.